Whirlpool W7I HF60 TU - User Manual

ENDaily Reference Guide
1
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.whirlpool.eu/register
1. ON-OFF/Reset button with indicator light
2. Eco program button with indicator light
3. Auto Intensive program button with indicator light
4. Auto Mixed program button with indicator light
5. Auto Fast program button with indicator light
6. Rapid program button with indicator light
7. Crystals program button with indicator light/ Self-Clean program - 3 sec. press
8. Prewash program button with indicator light
9. Salt reservoir empty indicator light
10. Rinse Aid reservoir empty indicator light
11. Display
12. Program number and remaining time indicator
13. Closed water tap indicator light
14. DESCALE indicator light
15. Power Clean® option button with indicator light
16. Half Load option button with indicator light
17. Extra Dry option button with indicator light/ Settings - 3 sec. press
18. Silent option button with indicator light
19. Sani Rinse option button with indicator light
20. Turbo option button with indicator light
21. Delay option button with indicator light
22. START/Pause button with indicator light
SETTING MENU
1. Switch on the appliance by pressing the ON-OFF button.
2. Hold the Settings (Extra Dry ) button for 3 seconds, until you hear
a beep and the display shows „SEt”.
3. After one second the rst available setting (letter „h”) will be displayed.
4. Press Prewash program / Power Clean® option buttons to scroll
through the list of available settings (see table below), then press START/
Pause to view and change the value of currently selected setting.
5. Press Prewash program / Power Clean® option to change the
value, then press START/Pause to save the new value.
6. To change another setting, repeat points 2 and 5.
7. Press ON-OFF or wait 30 seconds to exit the menu.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light on the control
panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel (see gure) and ll the salt reservoir
right up to its edge (approximately 0,5 kg); it is not un-
usual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
LETTER SETTING
VALUES
(Default - in bold)
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”)
1 | 2 | 3 | 4 | 5
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”)
0 | 1 | 2 | 3 |
4 | 5
NaturalDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Time on the oor (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Sound
“1” = On, “0” = O
1 | 0
Internal Lights (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included in
the settings menu.
-
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
Setting the water hardness
To allow the water softener to work in a perfect way, it is essential that the
water hardness setting is based on the actual water hardness in your house.
This information can be obtained from your local water supplier. The facto-
ry setting is “3”. See „WATER HARDNESS TABLE”.
To change, follow instructions in section “SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing
scale buildup on the heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
the salt container when empty. The frequency of regeneration depends
on the water hardness level setting - regeneration takes place once per 4-6
Eco cycles with the water hardness level set to 3. The regeneration process
occurs at the beginning of the cycle with additional fresh water.
• Single regeneration consumes ~3L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be
lled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.
110 ml), making sure it does
not overow from the dis-
penser. If this happens, clean
the spill immediately with a
dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (Soft) 0 - 6 0 - 10 0 - 7
2 (Medium) 7 - 11 11 - 20 8 - 14
3 (Average) 12 - 16 21 - 29 15 - 20
4 (Hard) 17 - 34 30 - 60 21 - 42
5 (Very hard) 35 - 50 61 - 90 43 - 62
A
B
Before using the appliance carefully read
Safety and Installation Instructions. More information about your
product available on website: docs.whirlpool.eu
After installation, please remember to remove all transport protection
parts from the dishwasher.
CONTROL PANEL
FIRST TIME USE
DISPLAY ON THE FLOOR
1
3
2
1. Delay Time on the oor - indicator of the time left to the start of the cycle, when the Delay option is set
2. Salt reservoir empty - indicator light on the oor
3. Remaining Time on the oor - indicator of the time left to the end of the cycle
4 5 6 7 8 9 10 13 14 1511 12 16 17 18 191 2 3 20 21 22

Summary

CONTROL PANEL

Control Panel Overview

Details all buttons and indicator lights on the dishwasher control panel.

DISPLAY ON THE FLOOR

Floor Display Indicators

Explains the meaning of lights projected on the floor during operation.

FIRST TIME USE

Setting Menu

Guides through initial settings and menu navigation for appliance configuration.

Water Hardness Setting

Instructions on how to adjust water hardness for optimal performance.

Salt Reservoir Filling

Procedure for refilling the salt reservoir to prevent limescale buildup.

Rinse Aid Dispenser Filling

Guidance on filling the rinse aid dispenser for improved drying results.

DAILY USE

Daily Operation Steps

Covers checking connections, loading, program selection, starting, and ending cycles.

Program Modification and Interruptions

Explains how to change programs, add items, and handle cycle interruptions.

ADVICE AND TIPS

General Usage and Efficiency Advice

Provides tips on loading, energy saving, hygiene, and frost protection.

OPTIONS AND FUNCTIONS

Dishwasher Program Options

Details various selectable options like Power Clean, Half Load, Extra Dry, Delay, etc.

LOADING THE RACKS

Rack Loading Guidelines

Instructions for loading cutlery, upper rack, and lower rack for optimal washing.

CARE AND MAINTENANCE

Filter and Spray Arm Cleaning

Procedures for cleaning the dishwasher's filter assembly and spray arms.

TROUBLESHOOTING

Common Problems and Solutions

A guide to diagnose and resolve issues like no water, no start, no drain, or poor cleaning.

Whirlpool W7I HF60 TU Specifications

General

Door color	Not applicable
Water fill	Cold, Hot
Cord length	1.3 m
Control type	Touch
Product size	Full size (60 cm)
Inlet hose length	1.55 m
Number of baskets	2 basket(s)
Custom panel-ready	Yes
Outlet hose length	1.5 m
Appliance placement	Fully built-in
Control panel color	Black
Cutlery compartment type	Basket
Baskets adjustable placement	Upper
LED program stage indicator	No
Cycle time	270 min
Noise level	40 dB
Drying system	Natural
Delay start (max)	24 h
Dishwashing programs	Self-Clean 65°C, Eco 50°C, Auto-Mixed, Pre-wash, Quick 45°C, Daily 50°C, Intensive 65°C, Delicate 45°C
Number of place settings	15 place settings
Number of washing programs	8
Maximum hot water supply temperature	60 °C
Package depth	675 mm
Package width	625 mm
Package height	910 mm
Package weight	37500 g
Current	10 A
Connected load	1900 W
AC input voltage	220-240 V
AC input frequency	50 Hz
Energy efficiency scale	A to G
Water consumption per cycle	9.5 L
Warranty period	10 year(s)

Weight and Dimensions

Depth	555 mm
Width	598 mm
Height	820 mm
Weight	35500 g
Installation compartment depth	560 mm
Installation compartment width	600 mm
Installation compartment height (max)	900 mm