Whirlpool WETLV27HW - User Manual

Other manuals for Whirlpool WETLV27HW

Use And Care Guide60 pages

Questions and Answers

J
John PooleAug 19, 2025
Why is my Whirlpool Washer/Dryer not running or filling?
- A
  Amy JohnsonAug 19, 2025
  If your Whirlpool Washer/Dryer won’t run, fill, or stops working, or the wash light remains on, ensure it's properly connected to a grounded outlet and receiving power, avoiding extension cords. The lid must be closed for the washer to operate. The washer will pause during certain cycles. If the washer is tightly packed, remove some items to redistribute the load evenly. Do not add more than one or two additional items after cycle has started or add more water to the washer. Reset a tripped circuit breaker or replace any blown fuses. If problems persist, consult an electrician.
T
Tyler TerrellAug 21, 2025
What to do if my Whirlpool Washer/Dryer is not draining or spinning?
- A
  allenjessicaAug 21, 2025
  If your Whirlpool Washer/Dryer isn't draining or spinning, and your loads are still wet, or the spin light remains on, it could be due to several reasons. Small items might be caught in the pump or between the basket and tub; make sure to empty pockets and use garment bags. The cycle might have a low spin speed; use a higher spin speed or select Drain & Spin to remove extra water. The washer may be tightly packed or unbalanced; rearrange the load evenly. Check the drain hose installation, ensuring it doesn't extend too far into the standpipe and isn't clogged. Too much detergent can also cause issues; always measure detergent according to the load size. To remove extra suds, select Quick Wash without adding detergent.
J
Jason TurnerAug 23, 2025
Why is the Lid Lock light flashing on my Whirlpool Washer/Dryer?
- Y
  ywaltersAug 23, 2025
  If the Lid Lock light is flashing on your Whirlpool Washer/Dryer, make sure the lid is fully closed, as the washer won't start with the lid open. If you've paused the cycle using the Start/Pause button, the lid will remain locked until the basket has completely stopped spinning, which may take several minutes, especially with large or heavy loads.
S
Stephanie TorresAug 26, 2025
How to prevent fabric damage in my Whirlpool Washer/Dryer?
- L
  Lisa RomeroAug 27, 2025
  To avoid fabric damage in your Whirlpool Washer/Dryer, empty pockets, zip zippers, and fasten hooks before washing to prevent snags. Tie strings and straps to prevent tangling. Mend any rips before washing. Ensure you load garments loosely and use the correct cycle for the fabric. Add only one or two garments after the washer has started. Do not pour liquid chlorine bleach directly onto the load and wipe up any spills. Always follow garment care label instructions. Undiluted bleach will damage fabrics, so do not use more than recommended.
A
Alexis KellyAug 28, 2025
How to prevent load from tangling in my Whirlpool Washer/Dryer?
- L
  Lynn LeeAug 28, 2025
  To avoid tangling in your Whirlpool Washer/Dryer, load garments loosely and evenly around the basket wall. Select a cycle with a slower wash action and spin speed, though items will be wetter. Mix types of load items and use the recommended cycle for the garments being washed.
H
Hector MorrisAug 30, 2025
How to improve cleaning and stain removal in my Whirlpool Washer/Dryer?
- A
  Alexander HaynesAug 30, 2025
  To ensure your Whirlpool Washer/Dryer cleans effectively and removes stains, do not add extra water to the washer, as it senses the load size and adds the correct amount. Load garments loosely and add detergent to the bottom of the basket before adding clothes. Only add one or two garments after the washer has started. Adding detergent on top of the load is not recommended.
H
hamiltonmarySep 1, 2025
Why are there dry spots on my load after a Whirlpool Washer/Dryer cycle?
- B
  brandonmillsSep 1, 2025
  If you find dry spots on your load after a cycle in your Whirlpool Washer/Dryer, try washing a smaller load or using the Heavy Duty cycle. The high spin speeds combined with airflow during the final spin can cause items near the top of the load to develop dry spots, which is normal. If the washer is tightly packed, use the Bulky Items cycle for a higher water fill. Only add one or two additional garments after the washer has started.
G
Gregory GonzalesSep 3, 2025
Why is my Whirlpool Washer/Dryer load not rinsed properly?
- C
  christopher33Sep 3, 2025
  If your Whirlpool Washer/Dryer is not rinsing properly, check that the hot and cold inlet hoses are not reversed and that both are attached with water flowing to the inlet valve. Ensure both hot and cold water faucets are turned on. Check the inlet valve screens for clogs and remove any kinks in the inlet hose. Use HE detergent and measure it correctly based on load size. Load garments loosely, as a tightly packed washer will not rinse well. Add only one or two garments after the washer has started and use a cycle designed for the fabrics being washed.
M
Ms. Cheryl DavisSep 5, 2025
Why are there residues remaining on my Whirlpool Washer/Dryer load after washing?
- M
  mendozakatherineSep 5, 2025
  If you notice residues remaining on your load after washing in your Whirlpool Washer/Dryer, it may be due to sand, pet hair, lint, detergent, bleach, or other residues requiring additional rinsing. Select the Heavy Duty cycle to resolve this.
G
Greg HarmonSep 7, 2025
Why are the wash temperatures incorrect in my Whirlpool Washer/Dryer?
- L
  Lisa GrossSep 7, 2025
  This Whirlpool Washer/Dryer uses cooler wash and rinse water temperatures than older models as part of energy-saving measures. Check that the hot and cold inlet hoses are not reversed. Both hoses must be attached to both the washer and faucet, with both hot and cold water flowing to the inlet valve. Also, ensure that inlet valve screens are not clogged and remove any kinks in the hoses.

Summary

Electrical Requirements

Product Dimensions

Overall Height and Width

Details the overall height (A) and width (B) of the laundry center.

Door and Depth Specifications

Provides dimensions related to doors, height to door bottom, and product depth.

Cord and Hose Placement

Specifies the position and length of the power cord and drain hose.

Installation Clearances

Closet Installation Guidelines

Details recommended spacing and ventilation for recessed or closet installations.

Whirlpool WETLV27HW Specifications

General

Brand	Whirlpool
Model	WETLV27HW
Appliance Category	Dryer
Fuel Type	Electric
Capacity	7.0 cu. ft.
Color	White
Dryer Venting	Vented
Control Type	Electronic
Wrinkle Control Option	Yes
Moisture Sensor	Yes
End of Cycle Signal	Yes
Power Source	Electric
Voltage	240 V
Amperage	30 A
Type	Electric
Temperature Settings	3
Width	29 in
Depth	28 inches