To Next PageTo Next PageWhy does my Whirlpool WFW8620HC beep when I press start?
If your Whirlpool washer is beeping when you touch START/PAUSE, it means the door isn't closed properly. Make sure to close the door completely.
Why won't the door lock on my Whirlpool WFW8620HC Washer?
If the display shows “F5” followed by “E2” or “F05” followed by “E02”, it means the washer door isn't locking. Press POWER to cancel the cycle. Make sure the door is fully closed and latched, and check inside the drum for items that might be preventing the door from closing properly.
How to stop my Whirlpool WFW8620HC Washer from vibrating?
To resolve excessive vibration, rocking, or “walking” in your Whirlpool washer: * Ensure the front and rear feet are firmly in contact with the floor and locked, with the jam nuts tight against the cabinet bottom. * Check the floor for flexing or sagging. If uneven, use a 3/4" (19 mm) piece of plywood underneath the washer. Avoid raised wooden platforms. * Avoid tightly packed or excessively large loads, and balance single items like rugs with a few extra items. * Make sure you have removed the shipping bolts from the back of the washer.
Why my Whirlpool Washer won’t start or fill with water?
If your Whirlpool washer won’t run or fill, or it stops working, ensure both inlet hoses are attached and have water flowing to the inlet valve, and that both hot and cold water faucets are turned on. Check the inlet valve screens for clogs and remove any kinks in the inlet hoses. Verify the power cord is plugged into a grounded 3-prong outlet, avoid using an extension cord or GFCI, and ensure the outlet has power. If problems persist, have an electrician check the voltage and reset any tripped circuit breakers or replace blown fuses.
What to do if “Sd” or “SUD” (excess suds) appears on my Whirlpool WFW8620HC Washer?
If the Whirlpool Washer displays “Sd” or “SUD,” it means there are too many suds. The washer is trying to reduce them. Let the washer continue its cycle. Make sure you're only using HE detergent and follow the detergent manufacturer’s instructions to determine the correct amount based on your load size. If the issue continues, consider switching to a different HE detergent.
What to do if my Whirlpool Washer displays a water supply error?
If the display shows “Lo” followed by “FL” or “F8” followed by “E1” or “Lo” followed by “FL” or “F08” followed by “E01”, it indicates a water supply error. The unit will drain for 8 minutes with the door locked, and this drain cycle must finish to reset the error code. Once done, press POWER once to clear the code, then again to restart the washer. If the code reappears, it is recommended to call for service. Also, ensure that both inlet hoses are properly attached and that water is flowing to the inlet valve, and both hot and cold water faucets are turned on. Check the inlet valve screens for clogs, remove any kinks in the inlet hose, and ensure auto shut-off connectors and hoses are correctly installed and functioning. Use only the manufacturer’s recommended inlet hoses.
Why is my Whirlpool WFW8620HC Washer beeping?
If your Whirlpool washer is making error beeps, it could be because the door hasn't been opened and closed for at least three cycles. This often happens when the washer is first turned on. Simply open and close the door to clear the display.
Why is my Whirlpool Washer leaking water?
If you notice water or suds leaking from the door or rear of your Whirlpool washer, it's often due to using non-HE detergent or too much HE detergent. Ensure you're using only HE detergent and measuring it according to the manufacturer's directions. When running the Clean Washer with affresh® cycle, use affresh® tablet or regular, non-thickened chlorine bleach. Periodically clean the underside of the door window to prevent leaks and be aware that water can drip off the inside of the door if opened during “Add Garment.”
Why is my Whirlpool WFW8620HC Washer not cleaning clothes well?
If your Whirlpool washer isn't cleaning or removing stains effectively, ensure you're loading it loosely to allow items to move freely. Refer to the “Cycle Guide” for load size recommendations. Use only HE detergent and follow the manufacturer's instructions for the correct amount based on load size and soil level. If you have hard water or a high level of iron, consider installing a water softener and/or iron filter.
Why is my Whirlpool WFW8620HC load not rinsing well?
If your Whirlpool washer load isn't rinsing properly, ensure the hot and cold inlet hoses are not reversed and that both are attached with water flowing to the inlet valves, and both faucets are on. Also, check for clogged inlet valve screens and remove any kinks in the inlet hoses. Make sure you're using only HE detergent in the correct amount, as non-HE detergent can cause issues. Avoid tightly packing the washer, and load only dry items, using a cycle designed for the fabrics being washed. Limit adding garments after the cycle starts.
General| Style | front load |
|---|---|
| Color | chrome shadow |
| Washer Capacity | 5 cu. ft. |
| Max Spin Speed | 1, 100 |
| Spin Speeds | 5 |
| Number of Cycles | 37; 12 (regular, normal, delicates, wrinkle control, bulky items, heavy duty, whites, sanitize, colors, cold wash, towels, quick) |
| Number of Options | 11 |
| Temperature Settings | 5 |
| Soil Levels | 3 |
| Internal Heater | no |
| Control Panel | touchpad |
| Cycle Signal | yes |
| Interior Light | no; led |
| Steam | yes |
| Add Wash | yes |
| Soak Settings | yes |
| Remote Control | no |
| Wi-Fi | no |
| Voltage | 120 volts |
| Frequency | 60 hz |
| Current | 15a |
Weight and Dimensions| Depth | 33 1/4 inch |
|---|---|
| Height | 38 5/8 inch |
| Width | 27 inch |
