Whirlpool WSIO 3T223 PE X Daily Reference Guide

Whirlpool WSIO 3T223 PE X

64 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

1

EN

Before using the appliance carefully read Safety Instructions guide.

APPLIANCE

PRODUCT DESCRIPTION

DAILY REFERENCE

GUIDE

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance, please

register your appliance on: www.whirlpool.eu/register

You can download the Safety Instructions

and the

User Manual, by visiting our website

docs.whirlpool.eu and following the Instructions on

the back of this booklet.

1. Upper rack

2. Foldable aps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Power Clean® support

7. Cutlery basket

8. Lower spray arm

9. Filter Assembly

10. Salt reservoir

11. Detergent and Rinse Aid dispensers

12. Rating plate

13. Control panel

6

1

2

3

4

5

7

8

10

9

1112

13

0000 000 00000

Service:

1112

1 2 3 4 5 6 7 8 9 10

11 12 13

1. ON-OFF/Reset button with indicator light

2. Program selection button

3. Salt rell indicator light

4. Rinse Aid rell indicator light

5. Program number and delay time indicator

6. Tablet indicator light

7. Display

CONTROL PANEL

8. Multizone indicator lights

9. Multizone button

10. Delay button

11. Sani Rinse button with indicator light

12. Power Clean® button with indicator light

13. START/Pause button with indicator light / Tab

Table of Contents

Other manuals for Whirlpool WSIO 3T223 PE X

User Manual16 pages

Questions and Answers:

E
Elizabeth DeleonAug 13, 2025
Why won't my Whirlpool Dishwasher start or respond to commands?
- N
  nbellAug 13, 2025
  Your Whirlpool Dishwasher might not start or respond to commands due to several reasons: * The appliance might not be plugged in properly; ensure the plug is fully inserted into the socket. * There may be a power outage; if so, open the dishwasher door, press the START/Pause button, and close the door within 4 seconds (the dishwasher doesn't restart automatically after a power outage). * The dishwasher door might not be closed properly; push the door vigorously until you hear a 'click'. * The cycle may have been interrupted by opening the door for more than 4 seconds; press START/Pause and close the door within 4 seconds. * As a general solution, try switching the appliance off and on again. If the problem persists, unplug it for 1 minute, then plug it back in.
R
russell66Aug 16, 2025
What to do if my Whirlpool Dishwasher is not cleaning dishes properly?
- M
  Michael BellAug 16, 2025
  If your Whirlpool dishwasher isn't cleaning dishes well, consider the following: * Ensure the crockery is arranged correctly so the spray arms can rotate freely. * Select an appropriate wash cycle for the load. * Make sure that you are using the correct amount of detergent and that it's suitable for dishwashers. * Verify that the rinse aid compartment cap is closed correctly. * Clean the filter assembly if it's soiled or clogged. * Fill the salt reservoir if it's empty.
K
Kimberly WallaceAug 20, 2025
What to do if my Whirlpool WSIO 3T223 PE X Dishwasher won't fill with water and shows H, 6 error?
- H
  hollandmatthewAug 20, 2025
  If your Whirlpool dishwasher isn't filling with water and displays 'H, 6' error, try these steps: * Ensure that there is water in the water supply and that the tap is open. * Check that the inlet hose is not bent. * Clean the sieve in the water inlet hose if it is clogged. After cleaning, turn the dishwasher off and on, then restart a new program.
J
jose83Aug 25, 2025
How to fix a Whirlpool Dishwasher that won’t drain and shows error code 3?
- N
  Natasha HamptonAug 25, 2025
  If your Whirlpool dishwasher won’t drain and the display shows error code 3, here’s what you can do: * First, wait until the wash cycle finishes completely. * Check the drain hose to ensure it is not bent. * Clean the sink drain pipe if it is blocked. * Clean the filter if it is clogged with food residues.
M
Megan FrazierAug 27, 2025
What causes excessive noise in my Whirlpool WSIO 3T223 PE X?
- J
  Jordan BrownAug 27, 2025
  Excessive noise in your Whirlpool dishwasher can be caused by: * Dishes rattling against each other; make sure to position the crockery correctly. * An excessive amount of foam; ensure the detergent is measured out correctly and is suitable for dishwashers. To address this, restart the current cycle without adding any detergent.
B
Brandy WhiteAug 31, 2025
Why does my Whirlpool WSIO 3T223 PE X Dishwasher stop mid-cycle and show error 15?
- L
  Laura WilcoxAug 31, 2025
  If your Whirlpool Dishwasher finishes the cycle prematurely and shows error 15, it could be due to: * The drain hose being positioned too low or siphoning into the home sewage system; check if the end of the drain hose is placed at the correct height and install an air admittance valve if necessary. * Air in the water supply; check the water supply for leaks or other issues letting air inside.
R
robinsonshaneSep 4, 2025
Why is the salt indicator lit on my Whirlpool Dishwasher?
- D
  Dr. Andrew BeltranSep 4, 2025
  The salt indicator on your Whirlpool Dishwasher is lit because the salt reservoir is empty. Refill it with salt. Note that the indicator may remain lit for several wash cycles after refilling. Also, adjust the water hardness setting according to the instructions.
T
Timothy BrownSep 8, 2025
Why is the rinse aid indicator lit on my Whirlpool Dishwasher?
- A
  Alexander LunaSep 8, 2025
  The rinse aid indicator is lit on your Whirlpool Dishwasher because the rinse aid dispenser is empty. Refill the dispenser with rinse aid. Note that the indicator may remain lit for several wash cycles after refilling.

Whirlpool WSIO 3T223 PE X Specifications

General

Cycle time	240 min
Noise level	43 dB
Delay start (max)	12 h
Delayed start timer	Yes
Repairability index	8.1
Dishwashing programs	Auto
Number of place settings	10 place settings
Number of washing programs	7
Door color	Not applicable
Cord length	1.3 m
Product size	Slimline (45 cm)
Inlet hose length	1.55 m
Outlet hose length	1.5 m
Appliance placement	Fully built-in
Control panel color	Stainless steel
Current	10 A
Connected load	1900 W
AC input voltage	220-240 V
AC input frequency	50 Hz
Energy efficiency scale	A to G
Power consumption (off)	0.5 W
Water consumption per cycle	9 L
Energy consumption per cycle	0.74 kWh
Feet adjustment	80 mm
Package weight	31600 g

Weight and Dimensions

Depth	555 mm
Width	448 mm
Height	900 mm
Weight	29600 g
Installation compartment depth	570 mm
Installation compartment width	600 mm
Installation compartment height (min)	820 mm

Related product manuals

Preview: Whirlpool WSIO 3O34 PFE X

Whirlpool WSIO 3O34 PFE X

Preview: Whirlpool Wsic3m17

Whirlpool Wsic3m17

Preview: Whirlpool WSIC 3M17

Whirlpool WSIC 3M17

Whirlpool WSIC 3M27

Whirlpool WSIC 3M27 C

Whirlpool WSIP 4O33 PFE

Preview: Whirlpool WSFC 3M17 X

Whirlpool WSFC 3M17 X

Whirlpool WSFO 3O23 PF

Whirlpool WSFO3T223PCX

Whirlpool WIC 3C26

Preview: Whirlpool WFW5620HW

Whirlpool WFW5620HW