Why are my wash or rinse temperatures incorrect on my Whirlpool WTW4850BW?
If the wash or rinse temperatures are incorrect on your Whirlpool Washer: * Check for proper water supply. Make sure hot and cold inlet hoses are not reversed. Both hoses must be attached to both the washer and faucet, and have both hot and cold water flowing to the inlet valve. * Ensure that the inlet valve screens are not clogged. * Remove any kinks in the hoses.
Why is my Whirlpool WTW4850BW leaking water?
If your Whirlpool Washer is leaking water, here are some things to check: * Ensure the washer is level, as water may splash off the basket if it is not. Also, check that the load is not unbalanced or tightly packed. * Tighten the fill-hose connections. * Make sure all four fill hose flat washers are properly seated. * Pull the drain hose from the washer cabinet and properly secure it to the drainpipe or laundry tub. Do not place tape over the drain opening. * Check household plumbing for leaks or a clogged sink or drain, as water can back up out of a clogged sink or drainpipe. * Ensure the washer is loaded as recommended, as improper loading can cause the basket to be out of alignment and cause water to splash off the tub.
Why is the locked light flashing on my Whirlpool WTW4850BW Washer?
If the locked light is flashing on your Whirlpool Washer: * Ensure the lid is closed. The washer will not start or fill with the lid open. * If a cycle was stopped or paused using the Start/Pause button, the washer may still be spinning. The lid will not unlock until the basket has stopped spinning, which may take several minutes if washing large loads or heavy fabrics.
Why is my Whirlpool WTW4850BW Washer not rinsing the load?
If your Whirlpool Washer is not rinsing the load properly: * Check for proper water supply. Make sure hot and cold inlet hoses are not reversed. Both hoses must be attached and have water flowing to the inlet valve. Both hot and cold water faucets must be on. * Ensure that the inlet valve screens on the washer are not clogged. Remove any kinks in the inlet hose. * Using too much detergent can prevent the washer from operating correctly. Always measure detergent and follow detergent directions based on load size and soil level. * The washer is less efficient at rinsing when the load is tightly packed.
How to prevent fabric damage when using Whirlpool WTW4850BW?
To prevent fabric damage when using your Whirlpool Washer: * Empty pockets, zip zippers, and snap or hook fasteners before washing to avoid snags and tears. * Tie all strings and straps before starting the wash load. * Mend rips and broken threads in seams before washing. * Load garments in loose heaps evenly around the basket wall. Load with dry items only. * Use a cycle designed for the fabrics being washed. * Add only 1 or 2 additional garments after the washer has started. * Do not pour liquid chlorine bleach directly onto the load. Wipe up bleach spills, as undiluted bleach will damage fabrics. Do not use more bleach than recommended by the manufacturer. * Do not place load items on top of the bleach dispenser when loading and unloading the washer.
Why is there sand, pet hair, or lint on my load after washing in Whirlpool Washer?
If you find sand, pet hair, lint, etc. on the load after washing in your Whirlpool Washer, it is possible that heavy sand, pet hair, lint, and detergent or bleach residues may require additional rinsing. Select 2 Rinses for the selected cycle.
Why is my Whirlpool WTW4850BW Washer not cleaning or removing stains?
If your Whirlpool Washer is not cleaning or removing stains effectively: * Ensure the washer is not overloaded, as it is less efficient at cleaning when the load is tightly packed. Load garments in loose heaps evenly around the basket wall. Load with dry items only. Add only 1 or 2 additional garments after the washer has started. * Add detergent, Oxi products, and color-safe bleach to the bottom of the basket before adding the load items. * Avoid using too much detergent, as suds can prevent the washer from operating correctly. Always measure detergent and follow manufacturer’s directions based on load size and soil level. * Use a higher soil level cycle option and warmer wash temperature to improve cleaning. Use the Heavy Duty cycle for tough cleaning. See the 'Cycle Guide' to m...
Why is the single-dose laundry packet not dissolving in my Whirlpool WTW4850BW?
If a single-dose laundry packet is not dissolving in your Whirlpool Washer, ensure the laundry packet is added to the washer basket before adding clothes. Follow the manufacturer’s instructions to avoid damage to your garments.
Why is my Whirlpool WTW4850BW humming?
If you hear a humming sound from your Whirlpool Washer, it may be due to load sensing. It is normal to hear the hum of the sensing spins after you have started the washer.
Why does my Whirlpool Washer have dry spots on load after cycle?
Dry spots on your load after a cycle in your Whirlpool Washer are normal. The high spin speeds combined with airflow during the final spin can cause items near the top of the load to develop dry spots.
Key precautions to reduce risks of fire, electric shock, or injury when using the washer.
Guidance on using High Efficiency (HE) detergents for optimal performance and to avoid issues.
Functions of the Start/Pause button, lid lock, and cycle status lights.
Sorting, preparing, and loading garments evenly into the washer for optimal results.
Instructions for adding products, selecting options, starting the wash, and managing operation.
Tips for keeping the washer clean and performing well, including detergent use and lid opening.
Understanding normal sounds, fixing water leaks, and addressing general performance problems.
Troubleshooting issues with draining, spinning, cleaning, stain removal, and detergent use.
General| Style | top load |
|---|---|
| Color | white |
| Washer Capacity | 3.6 cubic feet |
| Max Spin Speed | 800 revolutions per minute |
| Internal Heater | no |
| Control Panel | electronic |
| Delay Start / End | no |
| Child Lock | no |
| Cycle Signal | yes |
| Steam | no |
| Annual Energy Consumption | 159 kilowatt hours |
| Voltage | 120 volts |
| Current | 15 amperes |
Weight and Dimensions| Depth | 27 inches |
|---|---|
| Height | 43 inches |
| Width | 29 inches |
| Net Weight | 130 pounds |
To Next Page