Whistler WS1095 User Manual (English)

Other manuals for Whistler WS1095

Questions and Answers:

S
Sheila YoungAug 6, 2025
What to do if my Whistler Radio does not recognize the SD Card?
- D
  Dylan PriceAug 6, 2025
  If your Whistler Radio isn't recognizing the SD card, there are a few potential reasons. First, the SD card might not be properly formatted. Use the PC Application to reformat it, ensuring that if you use Windows, the card format is FAT or FAT32 with 32kB clusters, and all three boxes are checked. Another possibility is that the SD card isn't fully inserted. Press the SD card into the slot until you hear a click, ensuring it's completely in place. If neither of these solutions works, the SD card itself may be defective, and you should replace it with a new one.
K
Kathleen KelleyAug 10, 2025
What to do if my Whistler Radio shows 'Init SD Card'?
- C
  Cassandra GreenAug 10, 2025
  If your Whistler Radio displays 'Init SD Card' when you turn it on, it typically indicates an issue with the SD card. First, ensure that the SD card is properly formatted by using the PC Application to reformat it. If the issue persists, the SD card may not be fully inserted. Push the SD card into the slot until you hear a click, ensuring it's fully seated.
J
Jose SullivanAug 14, 2025
How to fix SD Card error messages on my Whistler Radio?
- S
  samuelreynoldsAug 14, 2025
  SD Card errors on your Whistler Radio can arise from various issues. Start by ensuring the SD card is fully inserted and locked in the slot. If errors persist, try these steps: * Reformat the SD card using the PC Application's "Prepare SD Card for use" option. * If reformatting doesn't resolve the issue, consider replacing the SD card. Specific errors like a full SD card may require reducing the configuration size, removing unnecessary audio recordings, or switching to a higher capacity SD card. For write-protected errors, re-insert the card, reformat using the PC Application, or replace the card if needed. If the error persists after these steps, contact Support and provide error code information.
J
Jacob SnyderAug 19, 2025
Why is my Whistler Radio on but not scanning?
- J
  Justin ChavezAug 19, 2025
  If your Whistler Radio is on but not scanning, the squelch may not be adjusted correctly. Try turning the squelch control clockwise.
P
Patricia ColonAug 25, 2025
Why does my Whistler Radio show 'Scanning not available'?
- W
  wardjasonAug 25, 2025
  If your Whistler Radio displays 'Scanning not available', and you're using the mobile wiring harness, the battery voltage may be too low. To prevent data corruption, all functions that write data to the SD card, including scanning, are disabled when the voltage is insufficient. Check the battery voltage to resolve this issue.
B
Brittany StarkAug 28, 2025
What to do if my Whistler Radio does not function?
- C
  Christine ReeseAug 28, 2025
  If your Whistler Radio isn't functioning, first ensure it's receiving power from an appropriate power source. If it is, remove the power, hold the power button for one minute, then release it and reconnect to the power source.

Whistler WS1095 Specifications

General

PC Connectivity	USB
Memory Banks	10
Display Type	LCD
PC Programmable	Yes
Close Call RF Capture	Yes
Priority Scan	Yes
Weather Alert	Yes
Frequency Range	25-1300 MHz
Modes	Analog
Display	LCD
Trunking Systems Supported	Motorola, EDACS, LTR
Power Source	AC adapter or 4 AA batteries
Battery Type	AA

Related product manuals

Whistler WS1098

72 pages

Whistler WS1095 Owner's Manual

Table of Contents

Other manuals for Whistler WS1095

Questions and Answers:

Whistler WS1095 Specifications

Related product manuals