Wolf BWL-1S-05 - User Manual

Other manuals for Wolf BWL-1S-05

Installation Instructions144 pages

Questions and Answers

J
Joshua RodriguezAug 19, 2025
What to do if my Wolf BWL-1S-05 electric heater is not connected?
- M
  mriosSep 12, 2025
  If the electric heater is not connected, check the lead and plug-in connection. If WP090 = OFF, acknowledge the fault. If the high limit safety cut-out of the electric heater has tripped, reset it before commissioning the heat pump. If there's scale build-up, ensure the installation instructions regarding hot water treatment have been followed and reset the high limit safety cut-out (after a maximum of 3 resets, replace the electric heater). If there is air in the electric heater, it may dry fire; in this case, replace the electric immersion heater.
N
njohnsonAug 21, 2025
What should I do if the DHW sensor is faulty in my Wolf Heat Pump?
- B
  Bruce MarshallAug 21, 2025
  If the DHW sensor is faulty, check the DHW cylinder temperature to ensure it is within the permissible range (0 … 95 °C). Also, check the lead and plug-in connection to the sensor. Verify the sensor's position and correct it if necessary. If these steps don't resolve the issue, check or replace the sensor.
M
Mark DavisAug 23, 2025
What to do if the boiler sensor is faulty in my Wolf Heat Pump?
- L
  Larry LopezAug 23, 2025
  If the boiler sensor is faulty, check the flow temperature (T_boiler) to ensure it is within the permissible range (0 … 95 °C). Inspect the lead and plug-in connection. If the issue persists, check or replace the sensor.
A
Aaron QuinnAug 26, 2025
What should I do if the outside sensor is faulty in my Wolf Heat Pump?
- B
  Brandi Davidson DVMAug 26, 2025
  If the outside sensor is faulty, check the lead and plug-in connection to the sensor. If the wiring is correct, check or replace the sensor.
S
Sylvia MitchellAug 28, 2025
What to do if the return temperature is outside the permissible range in my Wolf BWL-1S-05?
- B
  brownbrandonAug 28, 2025
  If the return temperature is outside the permissible range (0 … 95 °C), check the return temperature. Also, check the lead and plug-in connection to the sensor. If the issue continues, check or replace the sensor.
H
Hannah WeissAug 30, 2025
What does it mean if my Wolf Heat Pump says 'BCC missing'?
- A
  Anna LopezAug 30, 2025
  If the display shows 'BCC missing', it indicates that the appliance type connector is missing. Insert the suitable appliance type connector to resolve this.
T
tanyabrownSep 1, 2025
What does it mean if my Wolf BWL-1S-05 says 'BCC incompatible'?
- C
  Christopher HermanSep 1, 2025
  If the display shows 'BCC incompatible', it means the wrong appliance type connector is installed. You should insert the correct appliance type connector.
C
Christina TranSep 3, 2025
What should I do if the header sensor is faulty in my Wolf BWL-1S-05 Heat Pump?
- M
  Martin JonesSep 3, 2025
  If the header sensor is faulty, check the lead and plug-in connection to the sensor. Also, check the position of the sensor and correct it if necessary. If problems persist, check or replace the sensor.
J
Juan NealSep 5, 2025
What should I check if the flow temperature (AWO T_boiler) is outside permissible range in my Wolf Heat Pump?
- C
  Curtis RobinsonSep 5, 2025
  If the flow temperature (AWO T_boiler) is outside the permissible range, check the flow temperature (AWO T_boiler). Also, check the lead and plug-in connection to the sensor. If the issue persists, check or replace the sensor.
E
Eric PottsSep 7, 2025
What to do if the pressure is outside permissible range in my Wolf BWL-1S-05 Heat Pump?
- D
  Donald StoneSep 7, 2025
  If the pressure is outside the permissible range, check the refrigerant temperature (ICT). Also, check the lead and plug-in connection.