31 Assembly
MAN1256 (3/23/2018)
Install Driveline
1.
Lightly coat splitter gearbox shaft with grease.
2.
Remove cap screw and lock nut from yoke on slip clutch end of driveline
(12). Attach driveline to input shaft of gearbox. Reinstall cap screw and
lock nut through driveline yoke and groove on input shaft.
Figure 35
. DS8.30E & DS10.40E Mounted Assembly
FILL GEARBOXES
NOTICE
■
Gearbox is not filled at the factory. Prior to delivery to customer,
make sure gearbox is filled only half-full with 80W or 90W API GL-4 or GL-
5 gear lube. Use side plug to remove any excess oil.
1.
Make sure vent plug hole is clear (installed by dealer).
2.
Remove plug on side of gearbox.
3.
Fill gearbox until oil runs out the side plug on gearbox. Use a high quality
gear oil with a viscosity index of 80W or 90W and an API service rating of
GL-4 or GL-5.
4.
Install side plug and vent plug.
INSTALL CHAIN SHIELDING
Full chain shielding must be installed at all times. Thrown objects
could injure people or damage property.
• If the machine is not equipped with full chain shielding, operation
must be stopped.
• This shielding is designed to reduce the risk of thrown objects.
The mower deck and protective devices cannot prevent all objects
from escaping the blade enclosure in every mowing condition. It is
possible for objects to ricochet and escape, traveling as much as 300
feet (92m).
1. A-Frame bar
2. Break link
3. Lift arm
4. Sleeve, 16.7 mm x 31.8 mm x 101.6 mm (.66
x 1.25 x 4.00)
5. Sleeve, 19.1 mm x 25.4 mm x 101.6 mm (3/4
x 1 x 4)
6. Headless pin, 19.1 mm x 143.0 mm (.75 x
5.63)
7. Sleeve, 15.9 mm x 25.4 mm x 31.8 mm (5/8 x
1 x 1-1/4)
8. Sleeve, 15.9 mm x 25.4 mm x 17.5 mm (5/8 x
1 x 11/16) (DS8.30E only)
8. Sleeve, 15.9 mm x 25.4 mm x 20.6 mm (5/8 x
1 x 13/16) (DS10.40E only)
9. Headless pin 22.2 mm x 176.2 mm (7/8 x 6-
15/16)
10.
Sleeve, 22.2 mm x 28.6 mm x 66.7 mm
(7/8 x 1-
1/8 x 2-5/8)
11. Sleeve, 23.8 mm x 36.5 mm x 69.9 mm
(15/16 x
1-7/16 x 2-3/4)
12.Driveline
13.Tailwheel arm
14.Tailwheel clevis
15.4 x 8 Rim & laminated tire
16.Hub, 4-bolt
17.Bushing, .25.1 mm x 35.4 mm
x 24.9
mm (.990 x 1.394 x .98)
18.M24 x 2.0 Axle bolt
19.1/4-28 Straight grease fitting
20.1/2 Flat washer
21.1/2 NC x 1 HHCS
22.Spirol pin, 10 mm x65 mm
23.M24 x 2.0 Slotted nut
24.Cotter pin
25.1-1/4 Std flat washer
26.1/4 x 1-1/2 Cotter pin
27.1/4 x 1-3/4 Klik pin
28.7/16 x 11/32 Klik pin
29.5/8 NC x 4-1/2 HHCS
30. 5/8 NC x 3 HHCS
31. 5/8 NC x 2 HHCS
32. 5/8 NC x 2 Carriage bolt (DS8.30E
only)
32. 5/8 NC x 2-1/2 Carriage bolt
(DS10.40E only)
33. 5/8 NC x 7 HHCS (DS8.30E only)
33. 3/4 NC x 6-1/2 HHCS (DS10.40E
only)
34. 5/8 NC Flanged lock nut (DS8.30E
only)
34. 3/4 NC Lock nut (DS10.40E only)
35. 5/8 Std flat washer
To Next Page
Loading...
