EasyManua.ls Logo

Woods RM990-3 - User Manual

Woods RM990-3
68 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OPERATOR'S MANUAL
REARMOUNT
MOWERS
20944
(Rev. 1/21/2010)
Tested. Proven. Unbeatable.
RM990-3
P990-3

Table of Contents

Questions and Answers

  • K
    kimberly67Aug 13, 2025
    How to stop belt slippage on Woods RM990-3?
    • T
      Tamara KellerAug 13, 2025
      Belt slippage on your Woods Lawn Mower can occur due to mower overloading from material that is too tall or heavy, oil contamination from over-lubrication, or the belt being obstructed. Reduce the tractor's ground speed while maintaining full PTO rpm. Consider cutting the material twice: once with a high pass and then at the desired height. Cut a partial swath. Avoid over-lubricating, clean any lubricant from the belt and pulleys with a clean rag, and replace any oil-soaked belts. Ensure the belt moves freely in the pulleys and belt guides, and check under the mower and around the blade spindle shafts for any foreign materials, cleaning them away.
  • J
    James BoydAug 16, 2025
    What causes belt rollover on a Woods RM990-3?
    • J
      jamesbowmanAug 17, 2025
      Belt rollover on your Woods Lawn Mower can be attributed to pulley misalignment, a damaged belt, foreign objects in the pulley grooves, or a worn pulley groove. Re-align the pulleys. Replace the belt. Inspect all pulley grooves for rust, paint, or weld spots and remove them. Consider replacing the pulley.
  • C
    Christopher AyersAug 20, 2025
    What to do if my Woods Lawn Mower is leaving streaks?
    • M
      mcdonaldtammyAug 20, 2025
      If your Woods Lawn Mower is leaving streaks, it could be due to several factors. The conditions might be too wet for mowing, preventing the blades from cutting grass pressed down by tractor tires, or the blades may be dull. Allow the grass to dry before mowing. Reduce the tractor's ground speed while maintaining full PTO rpm. Consider sharpening or replacing the blades.
  • B
    Bryan WelchAug 25, 2025
    Why is my Woods Lawn Mower discharging material unevenly?
    • M
      Matthew BurnsAug 25, 2025
      Uneven material discharge from your Woods Lawn Mower, resulting in bunches along the swath, can be caused by several issues. The material might be too high or too much, the grass could be wet, or the mower's rear might be too low, trapping material. To resolve this, reduce ground speed while maintaining 540 rpm at the tractor PTO, or make two passes over the material, raising the mower for the first pass and lowering it for the second, cutting at a 90° angle to the first pass. Also, raise the rear of the mower enough to allow material to discharge, but not so high as to cause other issues. Allow the grass to dry before mowing, and adjust the mower height and attitude.
  • J
    Jeremy RiosAug 28, 2025
    Why does my Woods Lawn Mower cut grass higher in the center?
    • A
      alyssajordanAug 28, 2025
      If your Woods Lawn Mower cuts grass higher in the center of the swath than at the edge, it's likely because the mower's rear is higher than the front. Adjust the mower height and attitude so that the rear and front are within 1/2" of the same height.
  • S
    Samantha WellsSep 1, 2025
    Why does my Woods RM990-3 cut grass lower in the center?
    • K
      karen91Sep 1, 2025
      If your Woods Lawn Mower cuts grass lower in the center of the swath than at the edge, it's likely because the mower's rear is lower than the front. Adjust the mower height and attitude so that the rear and front are 1/2" of the same height.
  • A
    Angela PowellSep 4, 2025
    Why are there frayed edges on my Woods RM990-3 Lawn Mower cover?
    • A
      Alejandro JohnsonSep 5, 2025
      Frayed edges on your Woods Lawn Mower cover may be due to a misaligned belt or the belt rubbing against a guide, or pulley misalignment. Re-align the belt or guide, ensuring the belt does not rub against any other part while running. Inspect to ensure the belt is running in the center of the backside idler, and shim the idler as necessary to align it.
  • R
    Rachel ClarkeSep 8, 2025
    What causes a damaged belt on Woods RM990-3?
    • A
      Ashley NunezSep 8, 2025
      A damaged belt on your Woods Lawn Mower can be caused by rollover, high shock loads, or damage during installation. Replace the belt.

Summary

SPECIFICATIONS

GENERAL INFORMATION

Provides general details about the mower and manual usage.

SAFETY RULES

TRAINING

Instructions and precautions for operator training and safe operation.

PREPARATION

Steps to ensure the mower and tractor are ready for safe operation.

OPERATIONAL SAFETY

Safety guidelines for operating the mower, including bystanders and thrown objects.

TRANSPORTATION

Safety rules for transporting the mower, including speed limits and slopes.

MAINTENANCE

Safety precautions to follow before performing maintenance or service.

OPERATION

ATTACHING RM990-3 MOUNTED MOWER TO TRACTOR

Step-by-step guide for connecting the RM990-3 mower to a tractor.

Cutting Height Adjustment

Procedures for adjusting the mower's cutting height for optimal performance.

ATTACHING P990-3 PULL-TYPE MOWER TO TRACTOR

Instructions for connecting the P990-3 mower to a tractor.

PRE-OPERATION CHECKLIST

Essential checks before starting the mower for safe operation.

OPERATING TECHNIQUE

Best practices for operating the mower under various conditions.

CLEANING

Procedures for cleaning the mower after use and for storage.

OWNER SERVICE

BLOCKING METHODS

Safe procedures for blocking the mower when working underneath it.

LUBRICATION INFORMATION

Details on lubrication points and frequency for mower maintenance.

BELT REPLACEMENT

Step-by-step guide for replacing the mower's belts.

BLADE SERVICING

Guidance on inspecting, sharpening, and replacing mower blades.

TROUBLESHOOTING

MOWING CONDITIONS

Common mowing problems and their solutions.

BELT CONDITIONS

Troubleshooting belt-related issues like slippage and breakage.

DEALER SERVICE

Blade Spindle Repair

Tips and procedures for repairing blade spindles.

Gearbox Maintenance

Information on maintaining and repairing the mower's gearbox.

ASSEMBLY

DEALER SET-UP INSTRUCTIONS

Instructions for dealers on how to set up the mower for customers.

Rear Driveline Installation

Steps to install the rear driveline assembly.

RM990-3 HITCH INSTALLATION

Guide for installing the hitch assembly on the RM990-3 model.

P990-3 Wheel Yoke Installation

Instructions for installing the wheel yoke on the P990-3 model.

DEALER CHECKLISTS

PRE-DELIVERY CHECKLIST

Checklist for dealers to ensure proper setup before delivery.

DELIVERY CHECKLIST

Checklist for dealers to review with the customer during delivery.

BOLT TORQUE CHART

BOLT SIZE CHART

ABBREVIATIONS

WARRANTY

Woods RM990-3 Specifications

General IconGeneral
BrandWoods
ModelRM990-3
CategoryLawn Mower
LanguageEnglish

Related product manuals