The Worldline Self/7000 and Self/8000 are modular unattended payment terminals designed for various applications such as petrol stations, transport, vending, and parking. These terminals are built to withstand both indoor and outdoor harsh weather conditions. The Self/8000 must always be connected to the Self/7000 master device. These two-component terminals are successors to the iSelf series and XENTEO Eco, aiming to enhance the unattended payment experience. They provide a complete solution for EMV payments and run ep2 applications from Worldline. Both terminals are PCI PTS 6.x certified, including SRED.
Self/7000
The Self/7000 is a hybrid card reader capable of processing contact, chip, and magnetic cards. It requires connection to a Self/8000 device to enable contactless card processing and PIN code entry. The Self/7000 is designed for rear installation in kiosks and complies with the EVA EPS (Compact Door Module) standard.
- Connectivity and Communications:
- Serial ports: COMO, COM2 (RJ11 and JST connectors).
- USB: 2x USB host (USB-A), 1x USB device (USB-B).
- Ethernet: 1x (RJ45).
- Add-on BOX connection: 2x.
- Self/8000 connection: 1x (HDMI).
- Audio output.
- Power or MDB Box (Optional).
- Radio (Optional).
- Technical Specifications:
- Mass: 825 g.
- Dimensions: 73.3 x 107 x 151.1 mm (height x width x depth).
- Power Supply: 9V-16V, 2A.
- Platform: Tetra.
- Memory: 512 Mb SDRAM and 512 Mb Flash.
- Functionality: Buzzer, Audio connector output, 1x Maintenance Button, 1x µSD, 2x SAM.
- Wake-up Mechanism: On RS232 connectors and card entry.
- Usage Features:
- SAM & µSD Installation: Disconnect from power, remove black silicon part, insert SAM cards (SAM slot 1 and/or 2) and SD card (µSD slot), replace black silicon part. Ensure correct corner angle for SAM cards.
- Buzzer: Controlled by the payment application, frequency driven by software.
- Card Entry: Guidance information can be displayed on the Self/8000 screen.
- Keyboard: A Self/8000 device must be connected to the Self/7000 for PIN entry. It features 10 digit keys, 4 function keys (correction/valid, cancel, reserved), and 2 contextual keys (*, #, or, up/down).
- Maintenance Button and LED: Located at the back. Press until blue LED lights on to restart the device.
- Audio Output: Connect to a 4 ohm speaker (2.8 W for optimal results). Connector: JST SM03B-SRSS-TB. Cable connector: Molex 105307-1202 + crimps 105300-2200.
- Hybrid Card Reader: Guided card input with backlight on the front side.
- Wake-up Function: Designed for "stand-by mode" to save power. Wake-up is triggered by setting PIN 2 of COMO or COM2 connection to "0" for at least 1 second. The wake-up PIN must be high impedance and voltage must not exceed 10V.
- Add-on Boxes: The Self/7000 can be upgraded with two types of add-on boxes: one for MDB features (power only or full MDB) and one for communication (Bluetooth and/or Radio link - 3G/4G EU/US/AUS standard). Installation involves powering off, removing the relevant cap from the rear casing, inserting the add-on box into slot 1 (MDB/PWR) or slot 2 (radio), and screwing it in with 0.8 Nm torque.
- Antenna Mounting: Remove the antenna tool, screw the antenna onto the connector, and place the tool back.
Self/8000
The Self/8000 is a compact PINPAD device supporting NFC/contactless card processing and PIN entry via a conventional keyboard. It cannot be used as a standalone device and must always be connected to a Self/7000. It is designed for easy installation (surface or rear mounted) in kiosks and complies with EVA EPS (Standard Door Module) or ARTEMA standards. Also referred to as Self/8000 CL to highlight its contactless capability.
- Connectivity and Communications:
- Power: 5V5 Max, 2A.
- USB Slave.
- IDMI port for connection to Self/7000.
- Technical Specifications:
- Mass: 963 g.
- Dimensions: 131.3 x 100 x 40.7 mm (height x width x depth).
- Power Supply: 2A 5V5.
- Platform: Tetra.
- Memory: Internal memory only.
- Link: 1x Self/7000 (Pin Out).
- Functionality: Contactless card reader, 2.5" Graphic display (320x160), Buzzer, 1x Maintenance button.
- Usage Features:
- Buzzer: Controlled by the payment application.
- Contactless LEDs & Contactless Logo: Information shown on the display according to EMVCo rules.
- Wake-up Function: Similar to Self/7000, designed for "stand-by mode". Wake-up is triggered by setting PIN 2 of COMO link to "0" for at least 1 second. The wake-up PIN must be high impedance and voltage must not exceed 10V.
General Product Installation
- Professional Installation Requirements: Installation must be performed by qualified electronics engineers in accordance with Worldline's recommendations and local regulations for electrical safety and radio emission levels.
- Packaging: Check the complete bill of material upon receipt. It includes 1 terminal, 1 fixing plate, 1 gasket, 1 power adaptor, and 1 HDMI cable. M4 locknuts and washers for mounting are not included.
- Location Selection: Terminals are designed for unattended indoor and outdoor use. Electrical installations must comply with local and regional codes (e.g., IEC).
- Select a convenient, accessible location on the machine.
- Ensure terminals fit the mounting position, card reader and PINPAD/NFC device face the cardholder, display is readable, and card slot is accessible.
- Ensure sufficient space inside the vending machine for mounting brace, ground connection, cable routing, and access to the rear side.
- Avoid exposure to rain or hostile weather.
- Mount vertically to reduce water ingress into the chip card reader.
- Ensure free air circulation around components.
- Take measures to avoid condensation/humidity in outdoor environments (e.g., heating/ventilation, keeping terminal active).
- Avoid direct sunlight on the display to prevent reflections.
- Ensure PIN privacy by locating the display outside the field of vision of cameras/mirrors and away from stairs.
- Use ESD protective clothing when handling devices.
- Regularly check for signs of tampering after installation.
- Product Gasket: Assemble correctly to ensure IP ratings.
- Evacuation Pipe (Self/7000): Guides water inside the kiosk. Ensure correct hose orientation.
- Installing the Modular Terminal:
- Gasket Positioning: Lugs (pins) in the rubber should fit into terminal openings.
- Mounting: Line up terminal with front panel opening, clamp EVA frame with four locknuts (not included), tighten in a Z-pattern. A cut-out with standard EVA EPS door module dimensions is required. Torque value: 1.0-1.3 Nm. Do not over-tighten nuts.
- Cabling: Connect communication cables after mounting.
- Powering: Plug in power plugs and wait for boot. Devices can be powered via MDV comm-box (MDB bus 48VDC) or external power supply (9V-48VDC).
Maintenance Features
- Configuration: Devices are delivered with an operating configuration loaded from the factory. Software and parameter definition files are installed. Configuration changes can be made by loading the latest software from SCS using the Self/7000 master device.
- Operating Life: Minimum operating life of 5 years.
- Cleaning Instructions:
- Disconnect all cables before cleaning.
- Clean the external front of the contactless reader regularly with a soft cloth slightly soaked in soapy water.
- Clean the glass carefully due to special surface treatment.
- Do not clean electronic components.
- Never use solvents, detergents, or abrasive cleaners.
- Avoid pressurized liquids.
- Do not expose to direct sunlight.
- Repairs and End of Life: Maintenance beyond manual description must be done by Worldline or an approved service center. Contact vendor for disposal information. Do not discard, give away, or sell terminals as they contain materials requiring professional handling for recycling. Products are labelled according to European Directives 2012/19/EU (WEEE) and 2006/66/EC (batteries and accumulators) for separate collection and recycling.
Safety Recommendations
- Operating Safety: Keep terminals away from heat, fire, high voltage, radiation, shocks, and abrasive chemicals. Ensure terminals are firmly fixed, kiosk/vending machine is protected from dust, sunlight, rain, wind, and flying parts, and operating temperature is between -20°C and 65°C. Use only supplied or compliant power adaptors. Disconnect power adaptor before cleaning or maintenance. Never drop, throw, slam, or vibrate terminals. Prevent liquids from entering. Do not use extension cables for power. Connect only recommended cables. Avoid storing/installing near excessive voltage fluctuation, electromagnetic fields, microwave radiation, deep freeze, or defrosting systems. Avoid storing near food or explosive substances. Never open terminals.
- Integrators: Implement procedures for regular on-site checks to ensure no cameras, skimming devices, or foreign objects are present. If suspicious activity or "tampered" warning message appears, disconnect power, alert police/computer crime unit, alert acquirer, and alter regulator. Integrators are responsible for compliance with local standards, integration rules, and industry practices. Worldline is not responsible for non-compliant integrations.
- Merchants: Check Self terminals daily for unusual cables, foreign objects in card readers, warning messages, visible damage, and matching serial numbers.
Technical Standards
- Electrical Consumptions: Max power supply 5V5 (via Self/7000), backup battery life 6 years of storage.
- Temperature and Humidity:
- Operating Conditions: Relative humidity 85% non-condensing at 40°C, external temperature -20°C to +65°C.
- Storage Conditions: Relative humidity 85% non-condensing at 55°C, external temperature -20°C to +70°C.
- Environmental Specifications:
- Storage Conditions: Front face shock resistance IK10.
- Vibrations Resistance: NF EN 60068-2-6 (10 tests sequences per axis): 5-9 Hz (3.3 mm amplitude), 9-200 Hz (10 m/s² acceleration), 200-500 Hz (15 m/s² acceleration). Endurance 30 min on each resonance frequency.
- Bumps Resistance: NF EN 60068-2-29. E (500 drops 1/2 sinus 25 g-6 ms each direction).
- Natural Events: Water and dust resistant IP65 (Self/8000 front face only).
- Degradation Specification: Vandal resistant, certified anti-tamper and attack resistant. Drop: -0.8 m on concrete.
- EC Marking: Conforms to IEC/EN 62368-1:2014, RE Directive 2014/53/EU. Radio: ETSI EN 300 330-1 V2.1.1. EMC: ETSI EN 301 489-1 V2.1.1, ETSI EN 301 489-3 V2.1.1.
Need help?
General
To Next Page
