To Next Page
A
Andrew WestSep 19, 2025
What to do if Worx Landroid L1000 Landroid flips over?
- BBrandi WrightSep 22, 2025
If your Worx Landroid flips over, there may be an inclined obstacle on the lawn. Exclude the obstacle from Landroid’s working area.
What to do if Worx Landroid L1000 Landroid flips over?
If your Worx Landroid flips over, there may be an inclined obstacle on the lawn. Exclude the obstacle from Landroid’s working area.
What to do if Worx Landroid L1000 does not charge?
If your Worx Lawn Mower isn't charging, first ensure the power cord is properly connected to both the charger and a suitable power supply. Also, check that the charging strips on the mower are making contact with the center of the contact strips on the charging pile.
How to fix long charging time on Worx Landroid L1000 Lawn Mower?
If your Worx Lawn Mower takes longer to charge than expected, clean the contact pins on the charging pile and the charging strip on the Landroid with a cloth, as debris can cause poor connection. Also, the charging protection program might be active due to high temperature. If so, move the charging station to a shady area or wait for cooler temperatures.
What to do if Worx Lawn Mower operative system crashes?
If the Worx Landroid operative system crashes when charging or on standby, it may be due to a software or display fault. Restart Landroid.
Why does Worx Landroid L1000 slip going downhill?
If your Worx Landroid slips out of its working area when going downhill, it may be due to low grip of the drive wheels. Ensure the wheels are clean and free of mud for maximum grip.
Why Worx Lawn Mower turns on but the blade doesn't spin?
This is normal: when the Worx Landroid needs to recharge, the blade disc does not rotate while it is searching for the charging station automatically.
Why does Worx Lawn Mower run outside the boundary wire?
If your Worx Landroid runs outside the boundary wire, doesn't mow within a zone, or moves erratically near it, it could be due to: * The boundary wire of another Landroid or robotic mower being too close. Ensure at least 1m clearance between your boundary wire and any others. * Signal leakage in wet conditions where the wire has been joined or repaired incorrectly. Check boundary wire joints and insulate them for a waterproof connection. * Boundary wire electric signal leakage due to broken insulation. Repair damaged wire with the supplied connectors.
Why does my Worx Landroid L1000 Lawn Mower Landroid vibrate?
If your Worx Landroid vibrates, the blade disc may be unbalanced, or the blades may be damaged. Check the blades and replace them if damaged. Remove any debris or foreign objects from the blades and blade disc.
What to do if Worx Lawn Mower says outside working area?
If your Worx Landroid displays 'Outside working area!' even when inside the boundary, the boundary wire ends may be clamped incorrectly. Try reversing the boundary wire ends and reconnecting them to the charging station.
Why is there a red light on my Worx Landroid L1000 charging pile?
A red light on the Worx Lawn Mower charging pile indicates that the boundary wire isn’t connected. Verify the boundary wire is correctly connected to the charging station and inspect the wire for any breaks.
General| Model | Worx Landroid L1000 |
|---|---|
| Category | Lawn Mower |
| Cutting Width | 20 cm |
| Maximum Lawn Size | 1000 m² |
| Battery Type | Lithium-Ion |
| Battery Capacity | 4.0 Ah |
| Cutting Height | 30-60 mm |
| Connectivity | Wi-Fi |
| Slope Capability | 35% |
| Blade Type | 3 pivoting blades |
| Weather Resistance | IPX5 |
| Smart Navigation | Yes |
| App Control | Yes |
| Boundary Wire Required | Yes |
| Charging Time | 90 min |
