To Next Page
A
Austin BellSep 18, 2025
Why does my Worx Landroid WR208 Landroid Vision beep when adjusting time?
- SShari DeanSep 18, 2025
This is normal. Turn counter-clockwise to adjust.
Why does my Worx Landroid WR208 Landroid Vision beep when adjusting time?
This is normal. Turn counter-clockwise to adjust.
Why does the green light turn on early on my Worx Lawn Mower charging pile?
If the green light on your Worx Lawn Mower charging pile illuminates before charging is complete, the charging base may be overheating or overcooling. Move the charging base to a shaded area or allow it to reach a normal temperature.
What to do if Worx Lawn Mower Landroid Vision flips over?
If your Worx Lawn Mower Landroid Vision flips over, exclude any inclined obstacles from its working area.
What to do if my Worx Landroid WR208 does not charge?
If your Worx Lawn Mower isn't charging, check that the power cord is properly connected to both the charger and a suitable power supply. Also, ensure that the charging strips on the mower are making contact with the center of the charging contacts on the charging pile.
Why Worx Landroid WR208 Lawn Mower Landroid Vision cannot dock with the charging pile?
If your Worx Lawn Mower Landroid Vision is having trouble docking with the charging pile, it could be due to: * Environmental factors: Try restarting Landroid Vision. * Dirty charging strip: Clean the contact pins on both the charging pile and the Landroid Vision's charging strip with a cloth. * Obstructed QR code: Ensure the QR code is unobstructed and clear.
Why is the charging time of my Worx Landroid WR208 Lawn Mower longer than expected?
If the charging time for your Worx Lawn Mower is longer than expected: * Check for and clean any debris on the charging strip to ensure a good connection. * The charging protection program might be active due to high temperature. Place the charging base in a shaded area or wait for cooler temperatures.
What causes Worx Lawn Mower Landroid Vision to slip out of its working area?
If your Worx Lawn Mower Landroid Vision is slipping out of its designated area, consider the following: * Check the wheels: Ensure the wheels are clean and free of mud to maximize grip. * Assess the slope: Exclude areas with slopes steeper than 30% (17°) using a magnetic strip or a non-grass pathway wider than 2 inches (5 cm) beside the slope. * Recognition error: Remove any obstacles. Use a magnetic strip or create a non-grass pathway wider than 2 inches (5 cm) on the lawn edge to ensure correct mower function.
Why does my Worx Landroid WR208 Lawn Mower Landroid Vision stop in the working area?
If your Worx Lawn Mower Landroid Vision is stopping in the working area: * Make sure that there are no obstacles. * The cutting height may be set too low for the length or density of the grass. Try raising the cutting height.
Why Worx Lawn Mower Landroid Vision turns on, but the blade disc does not spin?
The blade disc on your Worx Lawn Mower Landroid Vision won't spin if it's searching for the charging base. This is normal behavior when it needs to recharge automatically.
Why does my Worx Landroid WR208 Lawn Mower Landroid Vision vibrate?
If your Worx Lawn Mower Landroid Vision is vibrating, the blade disc may be unbalanced or the blades may be damaged. Check the blades, replace them if damaged, and remove any debris or foreign objects from the blades and blade disc.
Covers general warnings, safe operation, battery safety, and preparation.
Details on operating the mower, keeping it clean, and storage.
Explains border management, obstacle avoidance, cut to edge, and all-day cutting.
Covers planning for charging base, RFID, and lawn patrol.
Guides for installing charging base, RFID, and connecting power.
Instructions for keeping blades sharp and cleaning the mower.
Lists error messages, causes, and troubleshooting steps.
General| Type | Robotic Lawn Mower |
|---|---|
| Cutting Height | 30-60 mm |
| Battery | Li-ion |
| Battery Capacity | 2.0 Ah |
| Area Coverage | Up to 800 m² |
| Maximum Slope | 35% |
| Working Time | 60 minutes |
| Blade Type | 3 pivoting blades |
| Charging Time | 90 minutes |
