What to do if my Worx Landroid M500 Plus is not charging?
If your Worx Lawn Mower isn't charging, first, check that the power cord is properly connected to both the charger and a suitable power supply. Also, ensure that the charging strips on the mower are making direct contact with the center of the contact strips on the charging pile.
Why is the charging time far more than expected for my Worx Landroid M500 Plus Lawn Mower?
An extended charging time for your Worx Lawn Mower can be due to a poor connection caused by debris on the charging strip. Clean the contact pins on both the charging pile and the charging strip using a cloth. Alternatively, the charging protection program might be activated because of high temperature. Try placing the charging station in a shady area or wait for the temperature to cool down.
Why is my Worx Lawn Mower cutting grass unevenly?
Uneven grass cutting by your Worx Lawn Mower can occur for several reasons: * The mower isn't running enough hours daily, so consider increasing the mowing schedule. * The mowing area might be too large; try decreasing the area or increasing working time. * Dull blades can be the culprit, so replace them along with the screws to balance the blade disc. * The cutting height may be too low; raise it and then gradually lower it to the desired level. * Grass or objects might be wrapped around the blade disc; inspect and remove any obstructions. * There could be a buildup of grass in the blade disc or motor frame; ensure the blade disc rotates freely, removing debris if necessary.
Why does my Worx Landroid M500 Plus Lawn Mower vibrate?
If your Worx Lawn Mower is vibrating, it could be due to an unbalanced blade disc or damaged blades. Check the blades for any damage and replace them if needed. Also, remove any debris or foreign objects that may be stuck to the blades or blade disc.
What to do if my Worx Lawn Mower displays ‘Outside working area!’?
If your Worx Lawn Mower displays 'Outside working area!' despite being within the boundary, the boundary wire ends may be clamped incorrectly. Try reversing the boundary wire ends and reconnecting them to the charging station.
Why is the LED light off on my Worx Landroid M500 Plus charging pile?
If the LED light on your Worx Lawn Mower charging pile isn't turning on, the cause might be a lack of power. Check that the charging station is correctly connected to the charger, and that the charger is connected to a working power supply.
What does a red light on the Worx Landroid M500 Plus Lawn Mower charging pile mean?
A red light on the Worx Lawn Mower charging pile indicates that the boundary wire isn’t connected. Verify that the boundary wire is correctly connected to the charging station and inspect the wire for any breaks.
Why isn't the blade spinning on my Worx Landroid M500 Plus Lawn Mower?
If your Worx Lawn Mower turns on but the blade disc doesn't spin, it's likely because the mower is in the process of searching for the charging station. This is normal behavior; the blade disc doesn't rotate while it's searching.
Read all safety warnings and instructions for safe operation and future reference.
Guidelines for safe use, including training, preparation, and operation.
General operational guidelines, including safety devices and avoiding rotating parts.
Keep parts tight, inspect, check blades, use correct charger, and clean contacts.
Do not dismantle, short-circuit, expose to heat, use correct charger, and charge before use.
Landroid safety warnings, Li-Ion battery hazards, and disposal instructions.
Information on blade rotation, lifespan, and replacement procedures.
Step-by-step guide on how to safely replace the mower blades.
Instructions for cleaning the upper body, bottom, drive wheels, and charging contacts.
Proper storage, operating temperature, and charging without boundary wire.
General| Model | Landroid M500 Plus |
|---|---|
| Category | Lawn Mower |
| Cutting Width | 18 cm |
| Max Lawn Size | 500 m² |
| Battery Type | Lithium-Ion |
| Battery Voltage | 20 V |
| Battery Capacity | 2.0 Ah |
| Cutting Height | 30-60 mm |
| Programmable | Yes |
| Rain Sensor | Yes |
| Charging Time | 90 min |
| Noise Level | 63 dB |
| Weather Resistance | IPX4 |
| Blade Type | 3 pivoting blades |
To Next Page