Worx WG788 - User Manual

Questions and Answers

H
harttinaAug 12, 2025
Why is my Worx WG788 Lawn Mower not running when I activate the switch lever?
- S
  Shaun WillisAug 12, 2025
  If your Worx Lawn Mower doesn’t run when the switch lever is activated, consider the following: * Check that the safety key is correctly installed and fully seated, and that the button on the switch housing is being completely pushed. * Release the switch lever to turn the mower off, remove the safety key, turn the mower over, and ensure the blade is free to turn. Remove any obstructions. If the blade is not free, return it to an authorized service center. The blade should turn freely. * Verify the battery is fully charged by plugging in the charger and waiting for the green light to illuminate.
H
Haley DennisAug 16, 2025
What to do if Worx Lawn Mower motor stops while mowing?
- A
  Ana SmithAug 16, 2025
  If your Worx Lawn Mower's motor stops while mowing, there are several potential solutions: * First, release the switch lever to turn the mower off and remove the safety key. Turn the mower over and check if the blade is free to turn, clearing any obstructions. * Second, raise the cutting height of the wheels to the highest position and restart the mower. * Third, ensure the battery has been fully charged by plugging in the charger and waiting for the green light. * Finally, avoid overloading the mower by slowing down the cutting pace or raising the cut height, or both.
C
Carla KingAug 20, 2025
What to do if Worx WG788 Lawn Mower cutting performance is unsatisfactory?
- M
  marcus88Aug 20, 2025
  If the cutting performance of your Worx Lawn Mower is unsatisfactory, or it does not cut the entire lawn, try these steps: * First, ensure the battery has been fully charged by plugging in the charger and waiting for the green light to illuminate. * Second, release the switch lever, remove the safety key, and turn the mower over to check the blade for sharpness. Keep the blade sharp. Also, inspect the deck and discharge chute for any clogging. * Finally, the wheel height adjustment may be set too low for the grass condition. Raise the cutting height.
A
Alexander UnderwoodAug 23, 2025
What to do if Worx WG788 Lawn Mower is not picking up clippings with bag?
- J
  Joseph MartinezAug 23, 2025
  If your Worx Lawn Mower is not picking up clippings with the bag, here are some things to check: * Ensure you remove the mulch plate when bagging. * Inspect the chute for clogs. If clogged, release the switch lever to turn the mower off, remove the safety key, and clear the chute of grass clippings. * If there is too much cut grass, raise the cutting height of the wheels to shorten the length of the cut. * If the bag is full, empty it more often.
G
Gregory AllenAug 28, 2025
What to do if Worx WG788 has clippings visible when mulching?
- K
  Kelly AdamsAug 28, 2025
  If there are clippings visible when mulching with your Worx Lawn Mower: * There may be too much cut grass. Raise the cutting height of the wheels to shorten the length of the cut. Do not cut off more than 1/3 of the total length. * Check the blade for sharpness and ensure it is always sharp.
C
christinalewisAug 31, 2025
What to do if Worx WG788 Lawn Mower battery charger LED’s not on?
- W
  wcomptonAug 31, 2025
  If the LED's on your Worx Lawn Mower battery charger are not on, check the plug connection and replace the charger if necessary.
B
Beth JacksonSep 3, 2025
What to do if Worx Lawn Mower is abnormally noisy and vibrates?
- D
  daniel49Sep 4, 2025
  If your Worx Lawn Mower is abnormally noisy and vibrates, take the following steps: * Release the switch lever to turn the mower off and remove the safety key. Turn the mower on its side and check the blade to ensure it hasn't been bent or damaged. If the blade is damaged, replace it with a replacement blade. If the underside of the deck is damaged, return the mower to an authorized service center. * If there is no visible damage to the blade and the mower still vibrates, release the switch lever to turn the mower off, remove the safety key, and remove the blade. Rotate the blade 180 degrees and retighten it. If the mower still vibrates, return the mower to an authorized service center.
C
Christopher PhillipsSep 7, 2025
Why is my Worx WG788 Lawn Mower too hard to push?
- L
  Laura YoungSep 7, 2025
  If your Worx Lawn Mower is too hard to push, raise the cutting height to reduce deck drag on the grass. Also, check each wheel for free rotation.