XCell Fury Extreme Assembly Manual
Page 4 of 138 Copyright Miniature Aircraft USA Created: 11/14/2006
This document may not be distributed without permission of Miniature Aircraft USA
3C.5 - Assemble Rudder Bellcrank...............................................................................................................................................................51
3C.6 - Install Rudder Bellcrank.....................................................................................................................................................................52
STEP #4 – FRAME ASSEMBLY.................................................................................................................................................................. 53
A) Chassis Components - Bag #4A........................................................................................................................................... 53
B) Engine Components - Bag #4B............................................................................................................................................. 54
4B.1 – Prepare Engine......................................................................................................................................................................................55
4B.2 – Install Engine Mounts.........................................................................................................................................................................57
4B.3 – Install Engine.........................................................................................................................................................................................59
C) Landing Gear - Bag #4C.......................................................................................................................................................... 60
4C.1 – Assemble/Install Landing Gear/Frame Bottom Plate..............................................................................................................60
D) Fan Shroud Mounts - Bag #4D.............................................................................................................................................. 62
4D.2 – Assemble/Install Fan Shroud/Mounts ..........................................................................................................................................63
4D.3 – Install Muffler ........................................................................................................................................................................................64
STEP #5 – FUEL TANK............................................................................................................................................................................. 67
A) Fuel Tank - Bag 5A.................................................................................................................................................................... 67
5A.1 - Assemble Fuel Tank.............................................................................................................................................................................68
5A.2 - Install Fuel Tank....................................................................................................................................................................................70
STEP #6 – SWASHPLATE/WASHOUT MIXER.......................................................................................................................................... 71
A) Swashplate - Bag #6A – Kit Specific.................................................................................................................................. 71
6A.1 - Assemble Swashplate..........................................................................................................................................................................72
6A.2 - Install Swashplate – 140° Kit...........................................................................................................................................................74
B) Washout Mixer - Bag #6B ....................................................................................................................................................... 75
6B.1 - Assemble Washout Mixer...................................................................................................................................................................76
6B.2 - Install Washout Mixer..........................................................................................................................................................................78
6B.3 – Assemble Swashplate Control Rods..............................................................................................................................................79
6B.4 – Install Swashplate Control Rods.....................................................................................................................................................79
STEP #7 – CONTROL SYSTEM/CANOPY ................................................................................................................................................. 80
A) Servo Mounts - Bag #7A......................................................................................................................................................... 80
7A.1 – Install Servos/Radio Gear.................................................................................................................................................................81
B) Ball Links - Bag #7B.................................................................................................................................................................. 84
C) Control Rods - Bag #7C........................................................................................................................................................... 85
7C.1 – Assemble Servo Control Rods .........................................................................................................................................................85
D) Servo Supports - Bag #7D...................................................................................................................................................... 87
7D.1 – Assemble/Install Servo Wheels......................................................................................................................................................88
7D.2 – Install Servo Control Rods................................................................................................................................................................90
7D.3 – Install Servo Supports .......................................................................................................................................................................91
E) Canopy Mounts - Bag #7E....................................................................................................................................................... 92
7E.1 – Assemble Canopy Knobs....................................................................................................................................................................92
F) Canopy – Box Contents............................................................................................................................................................ 93
7F.1 – Prepare Canopy.....................................................................................................................................................................................94
STEP #8 – ROTOR HEAD......................................................................................................................................................................... 95
A) Head Block - Bag #8A.............................................................................................................................................................. 95
8A.1 - Head Block Assembly ..........................................................................................................................................................................96
B) Blade Grips - Step #8B............................................................................................................................................................. 97
8B.1 – Assemble Bell Mixer ............................................................................................................................................................................98
8B.2 – Install Bell Mixers.................................................................................................................................................................................99
C) Head Axle Components - Bag #8C .................................................................................................................................... 100
8C.1 - Blade Arm Assembly..........................................................................................................................................................................101
8C.1 – Assemble Blade Arms.......................................................................................................................................................................101
8C.2 – Install Blade Arms..............................................................................................................................................................................103
D) Flybar - Bag #8D...................................................................................................................................................................... 104
8D.1 – Assemble/Install Flybar Control System...................................................................................................................................105
8D.2 – Assemble/Install Flybar Bell Links...............................................................................................................................................106
8D.3 – Install Flybar........................................................................................................................................................................................107
8D.4 – Install Flybar Paddles .......................................................................................................................................................................107
8D.5 – Install Rotor Head..............................................................................................................................................................................108
To Next Page
Loading...
Need help?
General