xLab TORPEDO VERSA 500 User Manual

4. Place the mount on the aerobars by placing each of the mounting
clamps onto the extensions. Ensure the clamp is secure and
completely touching the extensions.
3. Loosen the mounting clamp screws using the 3mm Hex Wrench.
5. Center the mounting plate and hand tighten each of
the screws.
6. Secure the Velcro straps by routing them through the clamps.
Pull the straps as tight as possible and attach them in place.
7. Tighten both mounting clamp screws to 35 in lbs (4.0 Nm).
TOOLS REQUIRED
MOUNTING TO BIKE
3mm Hex Wrench
Torque Wrench up to 35 in lbs (4.0 Nm)
HARDWARE
CAGE MOUNTING
M5 x 12mm
Socket Head
M5 x 14mm
Socket Head
M5 Flat Washer
(x2)
M5 Nylon Insert
Lock Nut (x2)
M5 Nylon Washer
M5 x 12mm Button Head
Flange Screw (x2)
MOUNTING CLAMP
M4 x 10mm
Flat Head Screw (x2)
M3 x 6mm
Flat Head Screw (x2)
Screw Post / Screw Spring
2. Remove the Torpedo Bottle from the cage by holding the mount and twisting the
bottle and pulling out.
M5 x 25mm
Flat Head Screw
IMPORTANT:
PLEASE COMPLETELY UNDERSTAND ALL USER INSTRUCTIONS AND SAFETY INFORMATION BEFORE USING THIS PRODUCT. AS WITH ANY HIGH TECH PRODUCT YOU WILL NEED TO
ROUTINELY CHECK FOR LOOSE HARDWARE, CRACKS OR OTHER DAMAGE AND REPLACE ITEMS AS NECESSARY. DO NOT USE PRODUCT IF ANY OF THESE CONDITIONS EXIST.
COMPUTER MOUNT
TORPEDO VERSA 500
TORPEDO VERSA 500
1. Rotate the top of the computer mount all the way forward to allow room for the bottle.
M4 x 20mm
Flat Head Screw
BOTTLE
Dolphin Breather Valve

xLab TORPEDO VERSA 500 Specifications

General

Product Type	Bicycle Light
Model	TORPEDO VERSA 500
Lumens	500
Weight	120g
Runtime	Up to 20 hours
Mount Type	Handlebar Mount
Light Modes	High, Medium, Low, Flash

Summary

Hardware Components

Cage Mounting Hardware

Lists M5 screws, washers, and nuts for cage attachment.

Computer Mount Hardware

Lists M5 and M3 screws for computer mount attachment.

Mounting Clamp Hardware

Lists M5 screws for mounting clamps.

Bottle Hardware

Lists the Dolphin Breather Valve.

Mounting to Bike

Tools Required for Mounting

Specifies the 3mm Hex Wrench and Torque Wrench.

Installation Procedure

Details steps for attaching the mount to aerobars, securing straps, and tightening screws.

Bottle Installation

Straw and Plug Configuration

Instructions for selecting straw hole, plug insertion, straw trimming, and positioning.

Dolphin Breather Valve Installation

Instructions for proper installation and sealing of the breather valve.

Bottle Seating and Retention

How to properly insert and lock the bottle into the cage.

Dolphin Tail Straw Management

Using the tail to tuck the straw out of the way.

Adjust Versa Computer Mount

Tools for Mount Adjustment

Specifies the 3mm Hex Wrench and Torque Wrench.

Computer Mount Adjustment Steps

Details loosening, adjusting height/angle, and tightening the mount.

Computer Mount for Other Types

Tools for Computer Attachment

Specifies the 2mm Hex Wrench and Torque Wrench.

Attaching Various Computers

Instructions for Garmin, Wahoo, Polar, and strap-mounted computers.

Bottle Care

Bottle Cleaning Procedure

Instructions for washing the bottle, straw, valve, and lid.

Straw Care

Cleaning the Straw

Specific instructions for washing the straw with a brush.

Warranty Information

Product Warranty Terms

Details limited warranty periods for different components.