WARRANTY
YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A
CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR
WARRANTY. PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF PURCHASE
AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY
QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE.
The benets provided under this warranty are in addition to other rights and remedies which are available to you at
law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to
a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty, however, where you have
suffered any additional direct loss as a result of a defective product you may be able to claim such expenses by
contacting our customer service helpline above.
1 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 12 months from the original date of purchase and is intended for DIY (Do It
Yourself) use only. If a product is defective it will be replaced in accordance with the terms of this warranty. Warranty
excludes consumable parts, for example: driver bits.
WARNING
The following actions will result in the warranty being void.
• Professional, Industrial or high frequency use.
• If the tool has been operated on a supply voltage other than that specied on the tool.
• If the tool shows signs of damage or defects caused by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
XU1
Australia/New Zealand (Head Ofce)
1-23 Letcon Drive, Bangholme, Victoria, Australia 3175
5
TROUBLESHOOTING
1. Not chiselling or low breaking power:
- Tool temperature is low;
- Accessories are not lubricated;
- Refer to the section ‘Cold Hammering’ below on how
to resolve this issue.
2. Accessory is jammed/stuck in concrete
during use:
- Release the accessory locking mechanism, allowing
the demolition breaker to be separated from the
accessory. The accessory should be easily removed
from the concrete once it is detached from the
demolition hammer.
3. Accessory repeatedly becomes stuck
while in use:
- Free the accessory as described above. Refrain
from penetrating too deeply with the chisel bit, as it
is prone to becoming stuck when demolishing large
pieces of concrete.
4. A small amount of sparking is visible
through the housing air vents:
- This is normal and does not indicate a problem.
5. Excessive sparking is visible through
the housing air vents and/or the
demolition breaker is failing to operate:
- This may indicate the carbon brushes have worn out
and need to be replaced. Carbon brushes should
only be replaced by a qualied electrician or power
tool repairer.
Cold Hammering
If the demolition hammer is stored for long periods
of time of at cold temperatures, the lubrication may
become stiff and the demolition hammer may not
hammer initially or the hammering may be weak.
Should this occur, insert an accessory into the
demolition hammer, turn the demolition hammer on
and apply the end of the accessory against a scrap
piece of concrete or timber. Turn the demolition
hammer on and off every few seconds. After 15
seconds to 2 minutes, the demolition hammer should
have started to hammer normally. The colder the
demolition hammer, the longer it may take to warm up
and function like normal.
Note: Always wait until the accessory has stopped
moving before putting down the demolition hammer.
To Next Page
Loading...
Need help?
General