Yamaha EMX 2000 - Input specifications; Output specifications

EMX2000
•
Input
specifications
Input
terminals
Gain
trim
Actuai load
impedance
For use
with
nominal
Input level
Connectors on
mixer
Sensitivity^
Max.
before dip
MIC
INPUT
(1-8)
MAX
MIN
5kn
50~600n Mies
-60
dB
(775
pV)
-16
dB
(123
mV)
-40
dB
(7.75
mV)
+4 dB
(1.23
V)
XLR-3-31 type^
LINE INPUT
(1-8)
MAX
MIN
50
kO
600Q
Lines
-34
dB
(15.5
mV)
+10 dB (2.45
V)
-14
dB
(155
mV)
+30
dB (24.5
V)
PHONE JACK (TRS)2
ST
INPUT
(9-12)
MAX
MIN
10
kO
6000
Lines
-34
dB
(15.5
mV)
+10
dB
(2.45
V)
-14
dB
(155
mV)
+30
dB
(24.5
V)
PHONE JACK^
ST SUB
IN
(1,2)
10
kO
6000
Lines +4
dB
(1.23
V)
+20
dB
(7.75
V)
TAPE
IN (L, R)
10
kn
6000 Lines
-10
dBV (316
mV)
+10 dBV (3.16
V)
PHONO JACK
CH
INSERT IN (1-4)
10
kO
6000 Lines 0
dB (775
mV)
+20 dB (7.75
V)
PHONE
JACK (1/0)3
POWER AMP IN (L,
R)
10
kO
6000
Lines
+4 dB (1.23
V)
+18
dB
(6.16
V)
PHONE JACK®
1 .
Sensitivity is
the lowest
level that can
produce
an output of
+4 dB
(
1 .23
V) or
the
nominal output level
when the unit is set at
maximum gain.
2. XLR type
connectors
and
PHONE JACKS
(TRS)
(T=HOT,
R=COLD,
S=GND)
are balanced.
3.
PHONE JACKS
are
unbalanced.
•
In these
specifications
when dB
represents a
specific
voltage, 0
dB is
referenced to 0.775
Vrms, 0
dBV is
referenced to 1
Vrms.
•
Output specifications
Output terminal
Actual
source
impedance
For use
with
nominal
Output
level
Connectors on
mixer
Nominal
Max. before cliping
STOUT1,2(L7R)
75fi
6000 Lines
+4dB(1.23
V)
+20 dB
(7.75
V)
PHONE JACK^
MONO OUT
750
6000
Lines
+4 dB
(1.23
V)
+20 dB
(7.75
V)
EFFECT
SEND
750
6000
Lines
+4 dB
(1.23
V) +20 dB (7.75
V)
MONITOR
OUT
1,2
750
6000 Lines
+4 dB
(1
.23
V) +20
dB
(7.75
V)
REC
OUT (L/R)
6000 10
kO Lines
-10
dBV
(31
6
mV)
+10 dBV
(3.16
V)
PHONO JACK
CH
INSERT
OUT
(1-4)
6000
1
0
kO Lines
0 dB
(775
mV)
PHONE JACK^
PHONES/
C.
R.OUT
for PHONES
1000
400 Phones
3mW
ST
PHONE JACK^
for C. R.
OUT
10 kO Lines
+4
dB
(1.23
V)
+20 dB
(7.75
V)
SPEAKER
OUT
1,2
(L/R)
0.10
4/80 Speaker
200
W/40
200 W/40
PHONE JACK^
BRIDGE OUT
0.10
80
Speaker
400 W/80
400 W/80
1 .
PHONE JACKS are balaned.
•
In
these specifications when dB
represents a specific
voltage, 0 dB is
referenced to
0.775 Vrms, 0
dBV is referenced
1 Vrms.
Specifications are subject to
change without
prior notice.
3