Yamaha FT50CET FT50GEHT

Questions and Answers

S
smaldonadoAug 18, 2025
What to do if Yamaha FT50CET FT50GEHT Outboard Motor fuel management gauge shows incorrect fuel consumption?
- E
  Elizabeth SchwartzAug 19, 2025
  If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
W
williamclarkAug 21, 2025
What to do if the Yamaha FT50CET FT50GEHT Outboard Motor gauge display does not wake up?
- D
  Dustin HooverAug 21, 2025
  If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
A
Amy FosterAug 23, 2025
Why Yamaha FT50CET FT50GEHT Outboard Motor illumination does not light?
- B
  Brandi JohnsonAug 23, 2025
  If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
D
Daisy JohnsonAug 26, 2025
How to fix Yamaha Outboard Motor tachometer showing incorrect engine RPM?
- D
  Debra PriceAug 26, 2025
  If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
C
cadamsAug 27, 2025
What causes Yamaha FT50CET FT50GEHT fuel management gauge to show incorrect remaining fuel?
- D
  David MaysAug 28, 2025
  If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
Z
zavalasarahAug 30, 2025
What to do if Yamaha Outboard Motor gauge shows “----”?
- S
  Suzanne SmithAug 30, 2025
  If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
N
nnguyenSep 1, 2025
Why Yamaha Outboard Motor Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
- R
  Robert DiazSep 2, 2025
  If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
L
Lisa GomezSep 3, 2025
How to fix Yamaha FT50CET FT50GEHT Outboard Motor trim gauge showing incorrect position?
- T
  Thomas CoxSep 3, 2025
  If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
J
John MillsSep 6, 2025
Why Yamaha FT50CET FT50GEHT Outboard Motor gauge operates unstably?
- W
  williamspatriciaSep 6, 2025
  If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
B
Brian HurstSep 8, 2025
What causes Yamaha FT50CET FT50GEHT gauge response to be poor or down?
- L
  Laura CastanedaSep 8, 2025
  If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.