What to do if Yamaha Outboard Motor fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
What to do if the Yamaha FT9.9GE Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha FT9.9GE illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha FT9.9GE tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha Outboard Motor fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
What to do if Yamaha FT9.9GE gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
Why Yamaha Outboard Motor Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
How to fix Yamaha FT9.9GE Outboard Motor trim gauge showing incorrect position?
If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
Why Yamaha FT9.9GE Outboard Motor gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
What causes Yamaha FT9.9GE Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
Detailed steps for safely uncrating the outboard motor from its steel frame packaging.
Guidance on proper outboard motor mounting for optimal performance and reliability.
Explains optimal water level guideline for 4-stroke motors to ensure performance and prevent damage.
Details on installing the remote oil tank for 2-stroke V4 and V6 oil injection engines.
Guidance on selecting the appropriate propeller based on application and load.
Table showing recommended engine RPM ranges for Wide-Open-Throttle operation.
Describes throttle control systems and lists remote control models and their applications.
Guidance on selecting and routing remote control cables for proper operation.
Overview of the multi-function tiller handle and its electrical functions.
Procedure for mounting gauges, including selection of location and angle.
Essential for outboard performance, monitors engine speed for efficient operation.
Digital tachometer with elapsed hour, trim, and oil warning indicators for engine speed monitoring.
Indicates boat speed by measuring water impact force, with calibration options.
Functions as fuel flow, consumption, economy gauge, and RPM synchronizer.
Warns of cooling system problems, shares sender with temp. meter on some models.
Indicates cooling water temperature, with a red zone for overheating warnings.
Wiring diagrams for single, twin, and triple engine configurations.
Procedure for initial setup of digital network gauges, especially for multi-engine setups.
Table of common system or gauge issues, their causes, and recommended measures.
Guidelines for selecting the correct battery capacity and type for Yamaha engines.
Instructions for battery wiring, including isolator-equipped models and house batteries.
Checklist for pre-delivery inspection to enhance customer satisfaction.
General| Brand | Yamaha |
|---|---|
| Model | FT9.9GE |
| Category | Outboard Motor |
| Language | English |
To Next Page
