What to do if Yamaha FT60DET fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
What to do if the Yamaha FT60DET gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha Outboard Motor tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha FT60DET fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
What to do if Yamaha FT60DET gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
Why Yamaha FT60DET Outboard Motor Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
How to fix Yamaha FT60DET Outboard Motor trim gauge showing incorrect position?
If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
Why Yamaha Outboard Motor gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
What causes Yamaha Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
Step-by-step guide for safely removing the outboard motor from its crate.
Detailed instructions for correctly mounting the outboard motor onto the transom.
Details the characteristics and types of Yamaha propellers for optimal engine performance.
Guidance on choosing the appropriate propeller based on boat load and operating conditions.
Provides recommended engine RPM ranges for Wide-Open-Throttle operation with different propellers.
Introduces the multi-function tiller handle and its electrical functions for various engines.
Step-by-step guide for installing various gauges onto a panel for proper operation.
Covers functions like fuel flow, consumption, and economy for efficient operation.
Provides representative wiring diagrams for remote controls and instruments for common configurations.
Provides solutions for common issues encountered with digital network gauges and systems.
Provides guidance on selecting the correct battery capacity and type for Yamaha outboard motors.
Details wiring procedures for single, twin, and isolator-equipped battery systems.
General| Maximum Output | 60 hp |
|---|---|
| Starting System | Electric |
| Full Throttle Operating Range | 5000-6000 rpm |
| Steering | Remote |
| Engine Type | 4-Stroke |
| Displacement | 996 cc |
| Fuel System | Electronic Fuel Injection |
| Bore x Stroke | 65 x 75 mm |
| Shaft Length | 20 in |
| Trim System | Power Trim & Tilt |
To Next Page
