Yamaha MFC05 User Manual

Congratulations!
You are the proud owner of a Yamaha MFCOS MIDI Foot
Controller. The MFCO5 makes control of MIDI instruments
and effect units more convenient by allowing programs 1
through 10 to be selected by simply tapping a footswitch.
The MFCOS is built to Yamaha’s rigid quality standards,
and will provide reliable service for many years if handled
properly
Please read this operation manual thoroughly before setting
up and using your MFCOS
1. PRECAUTIONS
® Keep the unit away from locations where it is likely to be
exposed to high temperatures or humidity—such as near
radiators, stoves, etc. Also avoid locations which are subject
to excessive dust accumulation or vibration which could
cause mechanical damage
® Strong physical shocks to the unit can cause damage. Handle
it with care.
® This product contains no user-serviceable parts. Refer all
maintenance to qualified Yamaha service personnel. Opening
the unit and/or tampering with the internal circuitry will
void the warranty.
® Always turn the power OFF prior to connecting or dis-
connecting cables, This is important to prevent damage to
the unit itself as well as other connected equipment
@ Always plug and unplug cables by gripping the connector,
not the cord.
® Never use solvents such as benzine or thinner to clean the
unit. Wipe clean with a soft, dry cloth.
@® The MECOS will run from dry batteries or an optional AC
adapter. Use ONLY the Yamaha PA-1 (B) AC adapter
when running the MFC05 from the AC mains. Attempting
to use other AC adapters can cause serious damage.
@ The MFCOS contains digital circuitry, and may cause
interference if placed too close to television or radio re-
ceivers, or other broadcast reception equipment. If inter-
ference occurs, move the MFCOS further away from the
affected equipment
© The MFCO5 should always be turned ON before other equip-
ment connected to it is turned ON
© If your MFCOS will not be used for an extended period of
time, remove the internal batteries. The AC adapter should
be unplugged from the AC mains outlet whenever the
MFCOS is not being used.
@ Always use the MFCOS with a properly constructed MIDI
cable. Never use a MIDI cable longer than 15 meters.
2. SETTING UP
Please set up the MFCOS according to the following procedure
@ Install the batteries as described in the previous section.
@ After making sure that both the MFCOS power switch and
the power switch of the equipment to be controlled are OFF,
connect an appropriate MIDI cable (less than 15 meters)
from the MFC05 MIDI OUT connector to the MIDI IN
connector on the receiving device. The receiving device can
be a MIDI synthesizer or a MIDI-controllable effect unit
such as the Yamaha REX50, SPX90 II, REVS, etc.
@ First turn the MFCOS power switch ON, and chen the power
switch of the receiving device. When the MFCOS power
switch is turned ON, the BANK A LED indicator will light.
@ Set the receive channel of the receiving MIDI device to either
1 or OMNI. The MFCOS transmits only on channel 1
© Since the MFCO5 transmits MIDI program change numbers
1 through 10, make sure the programs you wish to select on
the receiving device are stored in the appropriate memory
locations. If your receiving device uses a program change
assignment table, make sure it is set to to allow you to
select the desired programs
3. OPERATION
Operating the MFCOS is simplicity itself. You can transmit any
MIDI program change number from 1 (00) to 10 (09) simply
by pressing the appropriate program select footswitch, or the
bank select footswitch and one of the program select foot-
switches.
TTT RMS cos
a 5
= =
La | = J

Yamaha MFC05 Specifications

General

Brand	Yamaha
Model	MFC05
Category	Music Pedal
Language	English

Summary

Congratulations

Precautions

Handling and Environmental Precautions

Keep the unit away from heat, humidity, dust, and vibration. Handle with care to avoid damage.

Maintenance and Safety

Refer servicing to qualified personnel. Turn power off before connecting/disconnecting cables.

Setting Up the MFC05

Initial Setup Procedure

Connect MIDI cables and set up power, bank, and program change settings for operation.

Operation

Program Selection

Select MIDI program change numbers 1-10 using program select or bank select footswitches.

Battery Installation

Installing AA Batteries

Install 6 AA batteries, ensuring correct orientation and securing the battery compartment.

Specifications

Technical Specifications

Details on transmitted data, channels, connectors, power, dimensions, and accessories.

MIDI Data Format

Transmission Conditions and Data

Details program change transmission on Channel 1 with status and program number.

MIDI Implementation Chart

Function Transmittal and Recognition

Chart detailing functions transmitted and recognized by the MFC05, including MIDI modes.

FCC Information

Compliance and Interference Measures

Information on FCC compliance, radio noise, and measures to resolve interference issues.

Service and Support

Product Support Information

Details on worldwide service network, dealer contact, and customer support.