To Next PageTo Next PageWhat to do if the picture does not appear on my Yamaha Receiver?
If the picture does not appear when using your Yamaha Receiver, ensure that the output and input for the picture are connected to the same types of video jacks (e.g., composites, S-VIDEOs, or components) for both input and output.
How to fix a Yamaha RX-V1200 remote control that is not working?
If your Yamaha Receiver remote control isn't working correctly: * Ensure you are within a 6-meter range and no more than 30 degrees off-axis from the front panel. * Replace all batteries with new ones and press RESET. * If the microcomputer is frozen, remove the batteries from the battery compartment and then put them back.
Why is there no sound from the subwoofer connected to my Yamaha RX-V1200?
If you're not getting any sound from the subwoofer connected to your Yamaha Receiver: * When playing a Dolby Digital or DTS signal, ensure “1E LFE/BASS OUT” in the SET MENU is set to SWFR or BOTH. * When playing a 2-channel source, ensure “1E LFE/BASS OUT” in the SET MENU is set to BOTH.
What to do if the sound suddenly goes off on my Yamaha RX-V1200 Receiver?
If the sound suddenly cuts out on your Yamaha Receiver, here's what to check: * Verify the IMPEDANCE SELECTOR switch is set correctly, as the protection circuit may have been activated due to a short circuit. Then, turn the unit back on. * If the sleep timer has activated, turn the power back on and restart the source. * Ensure the unit isn't muted by pressing the MUTE button or any other operation buttons to cancel mute and adjust the volume.
How to improve noisy FM stereo reception on my Yamaha RX-V1200?
Noisy FM stereo reception on your Yamaha Receiver can often be improved by checking the antenna connections. If the transmitter is far away or the antenna input is poor, try using a high-quality directional FM antenna and use the manual tuning method.
How to turn on the on-screen display on a Yamaha RX-V1200 Receiver?
If the on-screen display isn't appearing on your Yamaha Receiver: * Check if the on-screen display setting is set to “DISPLAY OFF”. If so, select the full display or short display mode. * Ensure that the BLUE BACK setting under “9 DISPLAY SET” on the SET MENU is not set to OFF. Set BLUE BACK to AUTO to always show the OSD.
Why can't I record a source with my Yamaha RX-V1200 Receiver using the digital output jack?
If you cannot record a source using the digital output jack of your Yamaha Receiver, and the source component is only connected to the analog input jacks, connect the source component to the digital input jacks of the unit.
Why is there no sound from the rear center speaker on my Yamaha Receiver?
If you're not hearing sound from the rear center speaker on your Yamaha Receiver: * Ensure that “1D REAR CT SP” on the SET MENU is set to LRG or SML, not NONE. * Make sure 6.1/ES is turned on by pressing the 6.1/ES button on the remote control.
Why is there no sound from the effect speakers on my Yamaha RX-V1200 Receiver?
If you are not getting sound from the effect speakers on your Yamaha Receiver: * Ensure the sound effect is turned on by pressing STEREO. * If using a Dolby Surround, Dolby Digital, or DTS decoding DSP program with material not encoded with these formats, select another DSP program.
How to improve poor bass reproduction on Yamaha Receiver?
To improve poor bass reproduction on your Yamaha Receiver: * If “1E LFE/BASS OUT” in the SET MENU is set to SWFR or BOTH and you don't have a subwoofer, select MAIN. * Ensure the output mode for each speaker (main, center, rear, or rear center) in the SET MENU matches your speaker configuration; select the appropriate output mode based on the size of your speakers.
Audio Specifications| Minimum RMS Output Power | 80 W |
|---|---|
| DIN Standard Output Power | 145 W |
| Maximum Power (EIAJ) | 125 W |
| Dynamic Power | 105/130/170/200 W |
| Damping Factor | 80 or more |
| Frequency Response | 10 Hz to 100 kHz |
| Total Harmonic Distortion | 0.04% |
| Signal to Noise Ratio (IHF-A Network) | 86 dB / 81 dB |
| Residual Noise (IHF-A Network) | 150 µV or less |
| Channel Separation | 60 dB/45 dB |
| Tone Control BASS Boost/Cut | ±10 dB/50 Hz |
| Tone Control TREBLE Boost/Cut | ±10 dB/20 kHz |
| Phones Output | 150 mV/100 Ω |
| Input Sensitivity CD | 150 mV/47 kΩ |
| Output Level REC OUT | 150 mV/0.9 kΩ |
Video Specifications| Video Signal Type | NTSC or PAL |
|---|---|
| Composite Video Signal Level | 1 Vp-p/75 Ω |
| S-Video Signal Level Y | 1 Vp-p/75 Ω |
| S-Video Signal Level C | 0.286 Vp-p/75 Ω |
| Component Video Signal Level Y | 1 Vp-p/75 Ω |
| Component Video Signal Level PB/CB, PR/CR | 0.7 Vp-p/75 Ω |
| Signal to Noise Ratio | 50 dB |
| Frequency Response (MONITOR OUT) | 5 Hz to 10 MHz, –3 dB |
FM Specifications| Tuning Range | 87.5 to 107.9 MHz / 87.50 to 108.00 MHz |
|---|---|
| 50 dB Quieting Sensitivity | 2.0 µV / 25 µV |
| Selectivity | 70 dB |
| Signal to Noise Ratio | 76 dB / 70 dB |
| Harmonic Distortion | 0.2% / 0.3% |
| Stereo Separation | 45 dB |
| Frequency Response | 20 Hz to 15 kHz +0.5, –2 dB |
AM Specifications| Tuning Range | 530/531 to 1710/1611 kHz |
|---|---|
| Usable Sensitivity | 300 µV/m |
General Specifications| Dimension (W x H x D) | 435 x 171 x 432 mm |
|---|---|
| Weight | 15 kg |
| Power Supply | AC 120 V/60 Hz / AC 240 V/50 Hz / AC 230 V/50 Hz / AC 220 V/50 Hz / AC 110/120/220/240 V, 50/60 Hz |
| Power Consumption | 260 W / 270 W/370 VA / 360 W |
| AC Outlets | 2 (Total 80 W maximum) / 2 (Total 50 W maximum) / 2 (Total 100 W maximum) / 1 (100 W maximum) |
Verify insulation of exposed surfaces after service to prevent electrical hazards.
Diagram of the remote control for RX-V1200 and HTR-5490 models.
Remote control layout specific to RX-V1200RDS models.
Diagram of the remote control for the RX-V2200.
Details on audio output power, input sensitivity, video signal levels, and frequency response.
Details various RMS and maximum output power ratings for different channels and models.
Covers input sensitivity, impedance, output levels, and headphone jack specifications.
Introduction to the 18 diagnostic menu items and their sub-menus.
Diagnostic options for YSS938, DSP, HP Route, RAM Through, and Dolby Logic.
Diagnostic functions for speaker settings, VFD display, and manual tests.
Diagnostic checks for IF status, DSP RAM, and CS49329 messages.
Diagnostics for CS DL code, soft switch settings, and microprocessor information.
Procedures for entering, canceling, and managing DIAG mode.
How diagnostic menus and protection history are displayed on the unit.
Explains protection function history and common causes like excess current or heat.
Lists functions accessible during DIAG mode, excluding tuner settings.
Explains the signal path for YSS938 analog bypass and output levels.
Details on YSS938 0dB output, including head margin and reference data.
Information on YSS938 full bit output, specifying digital full bit without head margin.
Describes signal output with head margin for YSS 0dB, listing specific dBFS values.
Details on YSS full bit output, specifying digital full bit without head margin.
Details YSS-CS 0dB output, including head margin and reference data.
Information on YSS-CS full bit output, specifying digital full bit without head margin.
Details CS-YSS 0dB output, including head margin and reference data.
Information on CS-YSS full bit output, specifying digital full bit without head margin.
Describes HP 0dB output for YSS938, including head margin and reference data.
Information on HP full bit output, specifying digital full bit without head margin.
Details RAM 0dB signal output for YSS938, including head margin.
Details on PRO LOGIC I processing, including reference data and signal paths.
Information on PRO LOGIC II processing, including reference data and signal paths.
Explains NEO:6 processing by CS49329 and signal handling for DD/dts and AAC inputs.
Details the seven sub-menu items for speaker configuration (e.g., size, mix, rear settings).
Describes how to check the FL display section and OSD driver using sub-menu operations.
Explains the noise generator output for various channels and LFE frequency.
Used to reserve or inhibit backup RAM initialization for user settings.
Displays thermal/fan levels, REC-OUT function, and impedance/power limiter detection.
Displays IF status data and details for 1st, 2nd, and 3rd bytes of input/output settings.
Describes the signal format for digital reproduction, noting analog processing limitations.
Details signal processing status bits like mute requests and dts flashing.
Diagnoses bus connection for YSS938 and external RAM, checking for errors.
Displays CS49329 messages related to autodetection response.
Displays data version, TOC information, and sum calculated value of flash ROM for CS49329.
Used to switch function settings on PCB via software for product activation.
Procedure to confirm and adjust idling current of the main amplifier PCB.
Pinout diagram and block diagram for the YSS938-F DSP IC.
Detailed table describing the function and I/O type for each YSS938 pin.
Illustrates signal paths from input selector through DSP to power amplifiers.
Diagram showing video input selector, S-Video, and component video signal paths.
Schematic details of the DSP core, RAM, and interface circuits like ADC/DAC.
Schematic details for RDS decoder and video amplifier ICs.
Schematic details for RDS decoder and video amplifier ICs in RX-V2200.
Schematic details of power amplifier stages, protection circuits, and voltage measurements.
Schematic details of power supply circuits, voltage selectors, and regulators.
Schematic of the LCD panel and the main microcontroller for the remote.
Schematic of the LCD panel and main microcontroller for the RX-V2200 remote.
Table listing initial codes for remote control functions and their DSP/Zone2 compatibility.
