What does 'CHECK SP WIRES' mean on my Yamaha Receiver?
If your Yamaha Receiver displays “CHECK SP WIRES” on the front panel, it indicates that the speaker cables are short-circuited. To resolve this, ensure all speaker cables are correctly connected.
Why is there distortion on my Yamaha RX-V1900 Receiver even with a good FM antenna?
Distortion with clear reception, even with a good FM antenna, on your Yamaha Receiver suggests multi-path interference. Adjust the antenna position to eliminate it.
What to do if no sound is heard from the Yamaha RX-V1900 Receiver subwoofer?
If no sound is heard from the subwoofer when playing a Dolby Digital or DTS signal, set "LFE/BASS OUT" in "CONFIG" to "SWFR" or "FRONT" when a 2-channel source is being played.
What to do if my Yamaha RX-V1900 Receiver has buzzing and whining noises?
If you're hearing buzzing and whining noises from your Yamaha Receiver, it could be due to a nearby TV set. Move the unit away from the TV set.
Why can't I tune into the desired station with my Yamaha RX-V1900?
If you cannot tune into the desired station with the automatic tuning method on your Yamaha Receiver, the signal may be too weak. Try using a high-quality directional FM antenna.
What to do if Yamaha RX-V1900 Receiver audio input sources cannot be played in the desired digital audio signal format?
If the audio input sources cannot be played in the desired digital audio signal format, check whether "SUR. L/R SP" is set to "SMALL" or "LARGE" and configure "SUR.B L/R SP" properly.
Why is there no sound coming from my Yamaha RX-V1900 Receiver?
If you are experiencing a no sound issue with your Yamaha Receiver, there are several potential causes. First, ensure that all input and output cables are correctly connected; if the problem continues, the cables may be defective. Check that the audio input jack select is set to “AUTO”. Make sure that you have selected an appropriate input source using the INPUT selector. Also, verify that the volume isn't turned down or muted. Finally, ensure the source you are playing can be reproduced by the unit.
What to do if my Yamaha RX-V1900 remote control does not work?
If your Yamaha Receiver remote control isn't working properly, try these steps: * Replace the batteries. * Ensure the remote control is at the proper distance from the receiver. * Reposition the unit if direct sunlight or lighting is striking the remote control sensor. * Check that the operation mode selector is set correctly. * Verify the control zone setting. * Ensure the remote control code is correctly set using the “List of remote control codes”. * Match the remote control ID of the unit and the remote control.
How to fix Yamaha Receiver when there is no sound?
If you're experiencing a no sound issue with your Yamaha Receiver, consider the following: * Check and properly connect the input/output cables; if the problem persists, the cables may be defective. * Set the audio input jack to "AUTO". * Ensure an appropriate input source is selected using the INPUT selector. * Verify that the volume is not turned down or muted. * Make sure the source signals can be reproduced by the unit.
What to do if my Yamaha Receiver fails to turn on?
If your Yamaha Receiver fails to turn on or enters standby mode soon after being turned on, here are a few things to check: * Ensure the power cable is firmly connected. * Verify the speaker impedance setting matches your speakers. * Check speaker wire connections to ensure they are secure and not touching anything else. * If the unit experienced an electric shock, turn it off, disconnect the power, wait 30 seconds, and plug it back in.
General| Impedance | 4 Ω |
|---|---|
| RMS rated power | 910 W |
| Audio output channels | 7.1 channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.04 % |
| Equalizer | Yes |
| Product color | Black |
| AM band range | 87.5 - 108 kHz |
| FM band range | 530 - 1710 MHz |
| Supported radio bands | AM, FM |
| Dimensions (WxDxH) | 435 x 171 x 438.5 mm |
Weight and Dimensions| Weight | 17100 g |
|---|
Lists all parts that should be included in the package with the unit.
Instructions for inserting batteries into the remote control.
Guide to setting the voltage selector for local voltage.
Lists required and not included accessories for setup.
Instructions for setting up speakers and subwoofer.
Information on connecting speakers to the unit.
Detailed instructions for connecting speakers and handling wires.
Procedure to match the unit's impedance setting to speaker impedance.
Details on the HDMI input and output jacks.
Guides for optimizing speaker setup for one listening position.
Guides for optimizing speaker setup for multiple listening positions.
Step-by-step guide to basic playback operations.
Procedure for pairing Bluetooth receiver with a component.
Guides for navigating and configuring parameters in MANUAL SETUP.
Manually adjust basic speaker settings like CONFIG and LFE/bass out.
Saves favorite system settings for easy recall.
Recalls previously saved system settings.
Explains how to control the unit, TV, or other components via remote.
Guides on setting appropriate remote control codes for components.
Instructions for controlling the main unit using the remote control.
Accesses additional menus for adjusting unit operations.
General problems, causes, and remedies for unit malfunction.
Troubleshoots issues related to missing video output.
Troubleshoots lack of sound from surround speakers.
Addresses issues where the unit fails to operate correctly.
Troubleshoots problems related to HDMI connections.
Troubleshoots problems with the remote control's functionality.
Troubleshoots connection and playback issues with iPod.
Troubleshoots issues with USB device recognition and playback.
Troubleshoots errors and warnings during the AUTO SETUP procedure.
To Next Page
