To Next PageTo Next PageHow to enable Dolby Digital or DTS on Yamaha RX-V3300?
If your Yamaha Receiver is not playing Dolby Digital or DTS sources (the Dolby Digital or DTS indicator on the front panel display does not light up), ensure that “Digital output” and “Dolby Digital” or “DTS” are selected on the connected components. Refer to the operation instructions for your component for guidance.
Why does my Yamaha RX-V3300 Receiver suddenly turn into standby mode?
If your Yamaha Receiver suddenly turns into standby mode, it's possible the internal temperature has become too high, activating the overheat protection circuitry. Wait until the unit cools down and then turn it back on.
Why is there no sound from the subwoofer on my Yamaha RX-V3300?
If you're not getting any sound from the subwoofer connected to your Yamaha Receiver, consider the following: * If you are playing a Dolby Digital or DTS signal, ensure that “1E LFE/BASS OUT” on the SET MENU is set to SWFR or BOTH. * If you are playing a 2-channel source, set “1E LFE/BASS OUT” on the SET MENU to BOTH. * The source may not contain low bass signals (90 Hz and below).
Why is there no sound from the rear speakers on my Yamaha RX-V3300?
If you are not getting sound from the rear speakers of your Yamaha Receiver, consider the following: * Increase the output level of the rear speakers. * Ensure that “1C REAR L/R SP” on the SET MENU is set to the appropriate speaker mode for the rear L/R speakers. * If playing a monaural source, try selecting another DSP program, especially if program 11 is selected.
Why is there no sound from the center speaker on my Yamaha RX-V3300 Receiver?
To address the issue of no sound from the center speaker on your Yamaha Receiver: * Increase the output level of the center speaker. * Ensure that “1A CENTER SP” on the SET MENU is set to the appropriate mode for your center speaker, and not to NONE. * If you have selected one of the Hi-Fi DSP programs (1 to 6 except for Game and 8ch Stereo), try selecting another DSP program.
Why is there no sound from the effect speakers on my Yamaha RX-V3300?
If you are experiencing no sound from the effect speakers on your Yamaha Receiver: * Ensure that the sound effect is turned on by pressing STEREO/EFFECT. * The source encoded with a Dolby Digital or DTS signal may not have center, rear L/R, or rear center channel signals.
What does 'Check SP Wires' mean on my Yamaha RX-V3300 Receiver?
If “CHECK SP WIRES” appears on the front panel display of your Yamaha Receiver, it indicates that the speaker cables are short-circuited. Ensure that all speaker cables are connected correctly.
How to unlock sound field parameters on Yamaha RX-V3300 Receiver?
If the sound field parameters and other settings on your Yamaha Receiver cannot be changed, check if “14 MEMORY GUARD” on the SET MENU is set to ON. If it is, select OFF.
How to fix Yamaha Receiver on-screen display when it does not appear?
To address the issue of the on-screen display not appearing on your Yamaha Receiver: * Check if the on-screen display setting is set to “DISPLAY OFF”. If so, select the full display or short display mode. * Verify that the GRAY BACK setting under “13 DISPLAY SET” on the SET MENU is not set to OFF. Set GRAY BACK to AUTO to always show the OSD.
Why can only one speaker be heard on my Yamaha RX-V3300 Receiver?
To resolve the issue of only one speaker side being audible on your Yamaha Receiver: * Ensure that all cable connections are correct. If the problem persists, the cables may be faulty. * Check and adjust “3 L/R BALANCE” in the SET MENU to the correct position.
General| Channels | 7.1 |
|---|---|
| Power Output (8 ohms, 20Hz-20kHz, 0.06% THD) | 130W |
| Frequency Response | 10 Hz - 100 kHz |
| Total Harmonic Distortion | 0.06% |
| Input Sensitivity (line) | 200 mV |
| Input Sensitivity (MM) | 2.5 mV |
| Signal to noise ratio (line) | 100 dB |
| Damping factor | 100 |
| Channel separation (line) | 70 dB |
| Output (Pre out) | 1 V |
| Digital Inputs | 5 |
| Digital Inputs (Optical) | 3 |
| Digital Inputs (Coaxial) | 2 |
| Digital Outputs (Optical) | 1 |
| Digital Outputs (Coaxial) | 1 |
| Video Inputs (Composite) | 5 |
| Video Inputs (Component) | 2 |
| Video Outputs (Composite) | 2 |
| Video Outputs (S-Video) | 1 |
| Video Outputs (Component) | 1 |
| Audio Inputs (Analog) | 6 |
| Audio Outputs (Analog) | 2 |
| Surround Sound Modes | Dolby Digital, DTS, Dolby Pro Logic II |
| Tuner Type | FM/AM |
| Preset Stations | 40 |
| Weight | 17 kg |
| Power Output | 130W |
| Input Impedance | 47 kOhms |
| Speaker load impedance | 6 - 8 ohms |
Information on components with special characteristics requiring exact replacement.
Verification of insulation for exposed conductive surfaces on 120V models.
Detailed specifications for the audio output, including power and frequency response.
Specifications related to video signal input, output, and processing.
Specifications for FM tuner performance, including sensitivity and selectivity.
Specifications for AM tuner performance, including tuning range.
Details on power requirements, consumption, and standby power.
Physical dimensions and weight of the unit.
List of included accessories with the unit.
Configuration options for speaker setup, including size and bass management.
Procedure for testing low-frequency output and speaker settings.
Function to rename input sources for easier identification.
Assigning input sources to component video inputs.
Assigning input sources to optical audio inputs.
Assigning input sources to coaxial audio inputs.
Step-by-step instructions for removing the top cover of the unit.
Instructions for safely removing the front panel assembly.
Procedure for removing the bottom cover of the unit.
Steps for removing the DSP printed circuit board.
Instructions for removing the sub chassis assembly.
Procedure for removing the VIDEO (5) printed circuit board.
Steps for removing multiple VIDEO and FUNCTION PCBs.
Instructions for removing the MAIN (2) printed circuit board.
Steps for removing POWER and MAIN printed circuit boards.
List of available diagnostic menus and their sub-menu options.
Procedure for initiating the diagnostic mode on the unit.
How to start DIAG mode with protection functions disabled.
Steps to exit the diagnostic mode and restore normal operation.
Instructions on navigating and operating the DIAG menus and sub-menus.
Detailed explanations for specific DIAG menu items like YSS938 and DSP BYPASS.
Procedure for checking idling current in amplifier sections.
Diagrams indicating specific test points for amplifier checks.
Diagrams showing pin connections for display components.
Layout and assignment of grid elements for the display.
Detailed pinout and function description for the MB87J0470 IC.
Detailed pinout and function description for the YSS938 DSP IC.
First part of the overall system block diagram.
Second part of the overall system block diagram.
Component layout diagram for the DSP printed circuit board.
Component layout diagram for the FUNCTION printed circuit board.
Component layout diagrams for various OPERATION PCBs.
Component layout diagrams for various VIDEO PCBs.
Component layout diagrams for various MAIN PCBs.
Component layout diagrams for various POWER PCBs.
Detailed circuit diagram for the DSP section.
Detailed circuit diagram for the FUNCTION section.
Detailed circuit diagram for the OPERATION sections.
Detailed circuit diagram for the VIDEO section.
Detailed circuit diagram for the MAIN sections.
Detailed circuit diagram for the POWER sections.
List of electrical components with part numbers and descriptions.
Component list for the DSP printed circuit board.
Component list for the FUNCTION printed circuit board.
Component list for the POWER printed circuit board.
Component list for the VIDEO printed circuit board.
Component list for the MAIN printed circuit board.
List of chip resistors with values and part numbers.
List of mechanical parts with part numbers and descriptions.
List of parts for the front panel and sub chassis assembly.
List of parts for the heatsink assemblies (Left and Right units).
Explanation of initial codes and device/function assignments.
