Yamaha RX-V361 User Manual (English)

Other manuals for Yamaha RX-V361

Questions and Answers:

D
David WalkerAug 14, 2025
What to do if my Yamaha RX-V361 Receiver fails to turn on?
- J
  John AdamsAug 14, 2025
  If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, there are several potential causes. First, ensure the power cable is firmly connected. Second, verify that the speaker impedance setting matches your speakers. Third, check all speaker wire connections to ensure they are secure and not touching anything else. Finally, if the unit has been exposed to a strong electric shock, set it to standby, disconnect the power cable, wait 30 seconds, and plug it back in.
M
Mrs. Rachel SmithAug 17, 2025
Why is there no sound coming from my Yamaha RX-V361?
- Y
  yhebertAug 17, 2025
  If there is no sound from your Yamaha Receiver, check the following: Ensure the input and output cables are correctly connected (and not defective). Verify that an appropriate audio input jack is selected. Select the correct input source using the DINPUT l / h button on the front panel or the input selector buttons on the remote. Make sure the correct front speakers are selected with the 9SPEAKERS button. Also, check that the volume isn't turned down or muted (press NMUTE or QVOLUME +/- on the remote). Finally, ensure the source signals are compatible with the unit.
D
David GonzalezAug 21, 2025
What to do if the sound suddenly goes off on my Yamaha RX-V361 Receiver?
- C
  Cathy DavisAug 21, 2025
  If the sound from your Yamaha Receiver suddenly goes off, it could be due to a short circuit activating the protection circuitry. Check that the impedance setting is correct. It could also be that the sleep timer has turned off the unit. If so, turn the unit back on and play the source again.
B
Benjamin ParkerAug 25, 2025
Why is there no sound from the subwoofer on my Yamaha Receiver?
- B
  Brendan AtkinsAug 25, 2025
  If no sound is coming from the subwoofer connected to your Yamaha Receiver, check that “BASS OUT” in “SPEAKER SET” is set to “SWFR” or “FRNT” when a 2-channel source is being played, especially if you are playing a Dolby Digital or DTS signal. Also, the source may not contain low-frequency bass signals.
E
Edward DrakeAug 27, 2025
How to fix no sound from the center speaker on my Yamaha Receiver?
- S
  Stephanie MayAug 27, 2025
  If you're not hearing sound from the center speaker on your Yamaha Receiver, check the “SPEAKER SET” settings. If “CENTER” is set to “NONE”, change it to “SML” or “LRG”. Also, if you've selected a HiFi DSP program (except for 5ch Stereo), try a different sound field program. Finally, ensure that “SUR. LR” in “SPEAKER SET” is not set to “NONE”; if it is, set it to “SML” or “LRG.”
A
April RossAug 31, 2025
How to fix 'Check SP Wires' on Yamaha RX-V361?
- J
  josephdawnAug 31, 2025
  If “CHECK SP WIRES” appears on the front panel display of your Yamaha Receiver, it indicates that the speaker cables are short-circuited. To resolve this, ensure all speaker cables are correctly connected.
D
Dana GomezSep 3, 2025
Why is sound only coming from one speaker on my Yamaha Receiver?
- C
  Christopher MackSep 3, 2025
  If sound is only coming from one side or mainly the center speaker on your Yamaha Receiver, the issue could be due to several reasons. If playing a monaural source with a CINEMA DSP program, try another sound field program. Check that “CENTER” in “SPEAKER SET” is set to “SML” or “LRG,” not “NONE”. If a HiFi DSP program is selected (except for 5ch Stereo), try another sound field program. Ensure that “SUR. LR” in “SPEAKER SET” is set to “SML” or “LRG,” not “NONE”. Verify that the cables are correctly connected. Finally, adjust the “SP LEVEL” settings.
J
Jessica BrownSep 6, 2025
How to enable Dolby Digital on Yamaha Receiver?
- R
  Ronald RodriguezSep 6, 2025
  If your Yamaha Receiver is not playing Dolby Digital or DTS sources, first ensure that the connected component is set to output Dolby Digital or DTS digital signals by checking the component's operating instructions. Also, verify that the Audio input jack select is set to “AUTO”.
W
William MitchellSep 9, 2025
Why is my Yamaha RX-V361 humming?
- R
  Rebecca FoxSep 10, 2025
  If you hear a humming sound from your Yamaha Receiver, ensure the audio cables are firmly connected. If the problem persists, the cables may be defective.

Yamaha RX-V361 Specifications

General

Channels	5.1
HDMI Outputs	0
Dolby Digital	Yes
DTS	Yes
FM/AM Tuner	Yes
Response Bandwidth	10 Hz - 100 kHz
Signal-To-Noise Ratio	100 dB
Input Impedance	47 kOhm
Input Sensitivity	200 mV
Surround Sound Effects	Yes
Sound Effects	Yes
Tuner Type	Digital
Preset Station Qty	40
Width	435 mm
Height	151 mm
Frequency Response	10 Hz - 100 kHz
THD	0.9%
Audio D/A Converter	192kHz/24-bit
Built-in Decoders	Dolby Digital, DTS
Tuning Range	FM: 87.5 - 108 MHz, AM: 530 - 1710 kHz
Connector Type	1 x AM antenna, 1 x FM antenna, 1 x headphones (phone 6.3 mm), 1 x subwoofer output, 2 x audio input (RCA phono x 2), 2 x audio line-out (RCA phono x 2), 2 x composite video input (RCA phono), 2 x composite video output (RCA phono), 2 x HDMI input (19 pin HDMI Type A), 4 x S-video input (4 PIN mini-DIN), 1 x S-video output (4 PIN mini-DIN), 6 x speakers output (banana/spade x 2)
Total Harmonic Distortion	0.9%
Audio Inputs	2
Outputs	1 x subwoofer output
Dimensions	435 x 151 x 340mm