EasyManua.ls Logo

YATO YT-83114 - User Manual

YATO YT-83114
88 pages
Go to English
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
ELEKTRONICZNY TESTER AKUMULATORÓW
DIGITAL BATTERY TESTER
ELEKTRONISCHER BATTERIETESTER
ЭЛЕКТРОННЫЙ ТЕСТЕР АККУМУЛЯТОРОВ
ЕЛЕКТРОННИЙ ТЕСТЕР АКУМУЛЯТОРІВ
ELEKTRONINIS AKUMULIATORIŲ TESTERIS
ELEKTRONISKAIS AKUMULATORU TESTERIS
DIGITÁLNÍ TESTER AUTOBATERIÍ
ELEKTRONICKÝ TESTER AKUMULÁTOROV
ELEKTRONIKUS AKKUMULÁTOR TESZTER
TESTER ELECTRONIC ACUMULATORI
COMPROBADOR ELECTRÓNICO DE BATERÍAS
TESTEUR DE BATTERIE ÉLECTRONIQUE
TESTER ELETTRONICO PER BATTERIE
ELEKTRONISCHE BATTERIJTESTER
ΗΛΕΚΤΡΟΝΙΚΉ ΣΥΣΚΕΥΉ ΕΛΈΓΧΟΥ ΜΠΑΤΑΡΙΏΝ
ТЕСТЕР ЗА АКУМУЛАТОРИ ДИГИТАЛЕН
TESTADOR DE BATERIAS ELETRÓNICO
ELEKTRONSKI TESTER AKUMULATORA
ﻲﻣﻗرﻟا ﺔﯾرﺎطﺑﻟا رﺎﺑﺗﺧا زﺎﮭﺟ
YT-83114
PL
EN
DE
RU
UA
LT
LV
CZ
SK
HU
RO
ES
FR
IT
NL
GR
BG
PT
HR
AR
INSTRUKCJA ORYGINALNA

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the YATO YT-83114 and is the answer not in the manual?

Overview

The YATO YT-83114 is a portable and user-friendly electronic battery tester designed for 12V starter batteries and battery charging systems. It is always ready for operation as it draws power directly from the battery being tested, ensuring reliable and safe performance.

Function Description:

The device offers several testing functions accessible through its main menu:

  • Quick Test: Performs a rapid battery test.
  • Battery in Vehicle: Tests the battery while it's installed in the vehicle, including starter and alternator tests.
  • Out of Vehicle: Tests the battery when it's disconnected from the vehicle's power supply.
  • Voltometer: Displays the real-time battery voltage.
  • Reviewed Data: Shows the last saved battery test results.
  • System Setup: Allows configuration of tester settings, including language and screen contrast.

Important Technical Specifications:

  • Nominal Battery Voltage: 12V d.c.
  • Battery Voltage Measurement Range: 8-30V d.c.
  • Operating Conditions: Temperature: -10°C to 60°C, Relative Humidity: <80%.
  • Storage Conditions: Temperature: -20°C to 70°C, Relative Humidity: <80%.
  • Dimensions (L x W x H): 122 x 78 x 22 mm.
  • Supported Battery Types:
    • Regular flooded (standard lead-acid batteries)
    • EFB (Enhanced Flooded Battery) (lead-acid batteries with increased capacity)
    • AGM (Absorbed Glass Mat) (gel batteries with electrolyte absorbed in high-porosity fiberglass mats between plates)
    • Gel (gel batteries)
  • CCA Test Range: 100-2000 (CCA, BCI, CA, MCA, EN, SAE), 100-1400 (DIN, IEC), 26A17-245H52 (JIS), 30-220Ah (GB).

Usage Features:

  • Language Selection: The tester defaults to English. Users can change the language (e.g., to Polish, German, Russian, Ukrainian, Lithuanian, Latvian, Czech, Slovak, Hungarian, Italian, Dutch, Greek, Bulgarian, Portuguese, Romanian, Spanish, French, Croatian, Arabic) via the "System Setup" menu.
  • Quick Test Procedure: Select "Quick Test" from the menu, enter the nominal battery capacity (30-220 Ah), and confirm. The tester will display results such as "GOOD BATTERY" (battery OK), "GOOD RECHARGE" (battery OK, recharge), "REPLACE" (worn out, recommended replacement), "BAD CELL, REPLACE" (defective, replace), or "CHARGE-RETEST" (unstable operation, charge and retest).
  • In-Vehicle Battery Test: Select "Battery in Vehicle" then "Battery Test." Choose the battery type using arrows and confirm. After approximately 5 seconds, the results will be displayed.
  • Cranking (Starter) Test: From "Battery in Vehicle," select "Cranking Test," confirm, and start the vehicle engine. The tester automatically completes the test and displays the result. A starting voltage below 9.6V is typically considered incorrect.
  • Charging (Alternator) Test: From "Battery in Vehicle," select "Charging Test." Follow on-screen instructions:
    1. Turn off lights and AC for 10 seconds, press ENTER.
    2. Turn off all equipment, increase RPM to 2500-3000 for 10 seconds, press ENTER.
    3. Turn on lights and AC to maximum, idle engine for 10 seconds, press ENTER. Results will show "NORMAL" (normal output) or "NO OUTPUT" (no charge, check alternator).
  • Out-of-Vehicle Battery Test: Select "Out of Vehicle," choose the battery type, and confirm. Results will be displayed after about 5 seconds.
  • Voltometer Function: Select "Voltometer" to view real-time battery voltage.
  • Contrast Adjustment: In "System Setup," select "Contrast" and use arrows to adjust the screen contrast.

Maintenance Features:

  • Cleaning: Clean the tester housing with a slightly damp cloth (water) and wipe it dry. Never immerse the tester in water or other liquids.
  • Clamp Care: Keep the tester clamps clean. If corrosion or patina is present, clean the metal parts with a cleaning agent suitable for copper electrical terminals.
  • Storage: Store the tester separately to protect it from impacts (e.g., from other tools in a toolbox). The storage area should be shaded, well-ventilated, and protected from unauthorized access, especially by children.
  • Environmental Safety: Maintain a safe and well-lit work environment, free from obstacles, grease, oil, debris, and other waste.
  • Safety Precautions: Avoid contact with hot engine parts. Do not smoke or use open flames near fuel, engine, or battery. Be aware that lead-acid batteries produce potentially explosive gases. Avoid contact with electrolyte (sulfuric acid) as it is highly corrosive. Ensure the battery testing area is well-ventilated. Always read and follow the safety instructions provided with the battery.

YATO YT-83114 Specifications

General IconGeneral
BrandYATO
ModelYT-83114
CategoryTest Equipment
LanguageEnglish

Related product manuals