To Next PageTo Next Page
Need help?Do you have a question about the York YDHF-39 and is the answer not in the manual?
Identifies the specific compressor models covered by this manual.
Provides essential safety information and warnings for operating and servicing the equipment.
Explains the meaning of hazard symbols used throughout the document.
Provides an overview of the compressor's design, materials, and operating principles.
Explains how to identify compressor models using nomenclature and data plates.
Outlines best practices for compressor disassembly, reassembly, and part handling.
Details procedures for cleaning and inspecting compressor components for wear.
Provides guidance on safe and proper methods for lifting and moving the compressor or motor.
Lists and illustrates specialized tools required for compressor servicing and repairs.
Describes the steps involved in safely removing and installing the motor from the compressor.
Explains the types of shaft seals and procedures for their removal and installation.
Details the removal and installation procedures for bellows-type shaft seals.
Outlines the process for separating the rotor support from the rotor scroll for internal service.
Details the steps for removing the impeller, including specific procedures for different sizes.
Describes the process for removing the balance piston seal and diffuser plate assembly.
Details the procedure for removing the front low-speed bearings from the compressor.
Explains the steps for safely removing the front high-speed bearings.
Covers the removal of the bearing housing and associated gears.
Outlines the procedure for removing the rear low-speed bearing.
Details the removal of components associated with the rear high-speed bearings.
Specific instructions for removing rear high-speed bearings on HD and HF compressor models.
Provides installation steps for rear high-speed bearings on specific compressor design levels.
Details the installation process for rear high-speed bearings on HD and HF compressor models.
Instructions for installing the gears into the compressor assembly.
Steps for correctly installing the bearing housing onto the rotor support.
Guidance on installing the front high-speed bearings.
Procedures for installing the front low-speed bearings.
Covers the installation of the balance piston and diffuser plate assembly.
Details the process of installing the impeller onto the shaft.
Outlines the steps to disassemble the rotor scroll from the unit.
Describes how to remove the nozzle base plate from the rotor scroll housing.
Details the procedure for removing the impeller eye seal components.
Provides instructions for reassembling the eye seal for different compressor styles.
Covers the steps for reassembling the nozzle base plate.
Details the process of reassembling the scroll housing to the rotor support.
Outlines the procedure for removing the pre-rotation vane housing assembly.
Provides instructions for replacing the control shaft assembly.
Introduces the oil pump's function and service procedures.
Details the steps for safely removing the oil pump from the oil sump.
Outlines the procedure for taking apart the oil pump.
Provides steps for reassembling the oil pump.
Details the process for removing the drive gear from the pump assembly.
Covers the steps for reinstalling the complete oil pump and motor assembly into the oil sump.
Identifies the specific compressor models covered by this manual.
Provides essential safety information and warnings for operating and servicing the equipment.
Explains the meaning of hazard symbols used throughout the document.
Provides an overview of the compressor's design, materials, and operating principles.
Explains how to identify compressor models using nomenclature and data plates.
Outlines best practices for compressor disassembly, reassembly, and part handling.
Details procedures for cleaning and inspecting compressor components for wear.
Provides guidance on safe and proper methods for lifting and moving the compressor or motor.
Lists and illustrates specialized tools required for compressor servicing and repairs.
Describes the steps involved in safely removing and installing the motor from the compressor.
Explains the types of shaft seals and procedures for their removal and installation.
Details the removal and installation procedures for bellows-type shaft seals.
Outlines the process for separating the rotor support from the rotor scroll for internal service.
Details the steps for removing the impeller, including specific procedures for different sizes.
Describes the process for removing the balance piston seal and diffuser plate assembly.
Details the procedure for removing the front low-speed bearings from the compressor.
Explains the steps for safely removing the front high-speed bearings.
Covers the removal of the bearing housing and associated gears.
Outlines the procedure for removing the rear low-speed bearing.
Details the removal of components associated with the rear high-speed bearings.
Specific instructions for removing rear high-speed bearings on HD and HF compressor models.
Provides installation steps for rear high-speed bearings on specific compressor design levels.
Details the installation process for rear high-speed bearings on HD and HF compressor models.
Instructions for installing the gears into the compressor assembly.
Steps for correctly installing the bearing housing onto the rotor support.
Guidance on installing the front high-speed bearings.
Procedures for installing the front low-speed bearings.
Covers the installation of the balance piston and diffuser plate assembly.
Details the process of installing the impeller onto the shaft.
Outlines the steps to disassemble the rotor scroll from the unit.
Describes how to remove the nozzle base plate from the rotor scroll housing.
Details the procedure for removing the impeller eye seal components.
Provides instructions for reassembling the eye seal for different compressor styles.
Covers the steps for reassembling the nozzle base plate.
Details the process of reassembling the scroll housing to the rotor support.
Outlines the procedure for removing the pre-rotation vane housing assembly.
Provides instructions for replacing the control shaft assembly.
Introduces the oil pump's function and service procedures.
Details the steps for safely removing the oil pump from the oil sump.
Outlines the procedure for taking apart the oil pump.
Provides steps for reassembling the oil pump.
Details the process for removing the drive gear from the pump assembly.
Covers the steps for reinstalling the complete oil pump and motor assembly into the oil sump.
General| Brand | York |
|---|---|
| Model | YDHF-39 |
| Category | Air Compressor |
| Language | English |
