Young WIND TRACKER 06201 - Warranty; Specifications

Page 3
06201-90
BRIGHTNESS
AdjustdisplaybrightnessbyholdingtheBRIGHTkey.
MAXIMUM/WIND DIRECTION DIGITAL DISPLAY
The right display window can show either MAXIMUM WIND SPEED
or Numerical WIND DIRECTION. This selection is made in the setup
mode under Display (dSP).
REMOTE DISPLAYS
The WindTrackercan be used as a remote display by selecting
"InP SEr" during SETUP. Remote displays are connected to the
maindisplayusingtheRS-485terminals.Connectliketerminalsas
showninwiringdiagrams.Remotedisplaysshowexactlythesame
information as the main unit. MAX RESET and SETUP features are
controlledatthemainunitonly.Brightnesscanbeadjustedateach
displayindependently.Upto16remotedisplayscanbeconnected
to one main display.
VOLTAGE OUTPUTS
The Wind Tracker offers calibrated voltage outputs for both wind
speed and wind direction. This feature allows the use of recorders
andotherdevices.Fullscalevoltageforeachchannelis5.00VDC.
4-20 mA INPUTS
The Wind Tracker accepts 4-20 mA (Line Driver) inputs. The Line
Drivercircuitmustprovide0-50M/SWindSpeedscaling("M"sufx).
Connectcableasindicatedonpage4.SwitchonbackmustbeUPat
powerupforcorrect4-20mAoperation.SetINPUTto"LDI"inSETUP.
Note: 24 VDC power is required for line driver applications.
ERROR MESSAGES
The Wind Tracker detects and indicates two errors. Once corrected,
the error indication disappears.
DISPLAY
LDi Err 4-20 mA (line driver) signal is missing or out-
sideofacceptablerange.Verifyproperswitch
position or signal.
SEr Err UnitissettoreceiveRS-485serialsignal,(inP
SEr)butnoserialdataiscomingin.Verify
that the serial source is operating. Check
cablesforproperconnection.
WARRANTY
TheWindTrackeriswarrantedtobefreeofdefectsinmaterialsand
construction for a period of 12 months from date of purchase. Cover-
age is limited to repair or replacement of defective unit.
SPECIFICATIONS
Size: 144mm(5.65in)x144mm(5.65in)x  
36 mm (1.4 in)
PanelCutout:138mm(5.43in)x138mm(5.43in)
CompatibleSensors:
Wind Monitor
Wind Monitor-SE
Wind Monitor-MA
Wind Monitor-AQ
Wind Monitor-JR
Wind Sentry
OtherInputs: RS-485,4-20mA
Accuracy:  ±0.6%F.S.
Display Resolution:
  WindDirection: 10°circularpattern(36points)
      1°digitalw/dSP dIr selected
Wind Speed &
  Maximum: 1Knot,1MPH,1KM/H,0.1M/S
Voltage Outputs:
Wind Direction Range:
   0-5VDC 0-360°
Wind Speed Range: (dependent on units selected)
   0-5VDC  0-100Knots
0-100 MPH
0-200 KM/H
      0-50M/S
Alarm Relays: Non-latching
Normally Open contacts for WS and WD.
  Contactrating5Aresistive,
2A inductive @ 24 VAC, 30 VDC.
InputPower:12-30VDC,4.5W
Weight:1.0lb(0.45kg)withoutACadapter
CE COMPLIANCE
ThisproducthasbeentestedandshowntocomplywithEuropeanCE
requirementsfortheEMCDirective.Pleasenotethatshieldedcable
mustbeused.
Declaration of Conformity
R. M. Young Company
2801 Aero Park Drive
Traverse City, MI 49686 USA
Model 06201 WIND TRACKER
TheundersignedherebydeclaresonbehalfofR.M.
YoungCompanythattheabove-referencedproduct,to
which this declaration relates, is in conformity with the
provisions of:
CouncilDirective2004/108/EC(December15,2004)
onElectromagneticCompatibility
David Poinsett
R&D Manager