Z Corporation ZPrinter 650

Other manuals for Z Corporation ZPrinter 650

Troubleshooting Guide68 pages

Questions and Answers

K
Katherine JonesAug 20, 2025
Why does my Z Corporation 3D Printer say 'Head x temperature too high'?
- K
  Katelyn DouglasAug 20, 2025
  If your Z Corporation 3D printer displays the error 'Head x temperature too high', several factors could be responsible. First, verify the expiration date of the materials. Clean the print head contacts and Pogo Pins, then reinsert the print heads. If the issue persists, the print head may be old or defective and need replacement. Check the binder flow rate against the reference document. A worn service station wiper should be replaced with a 30011 Service Station Wiper. Ensure the parking spittoon is clean, and the air vent isn't clogged. Finally, troubleshoot the float switch and add binder if the printer is out of binder.
K
kevin36Aug 22, 2025
What to do if Z Corporation 3D Printer displays 'Head x fire voltage failed'?
- C
  Catherine GutierrezAug 22, 2025
  If your Z Corporation 3D printer shows the error 'Head x fire voltage failed', there are several possible causes. Start by cleaning the print head contacts and Pogo Pins, then reinsert the print heads. If the issue continues, the HP11 Print Head may be old or defective and require replacement. Another potential cause is a bad carriage cable, which would necessitate replacing the 50080 Pogo Flex Cable. Additionally, a bad Pogo PCB or a bad festoon cable assembly could be the problem, requiring replacement of the 50019 Pogo PCB or the 50108 Festoon Cable Assembly, respectively. In some cases, a failed PC104+ PCB may be the cause, needing replacement of the 50016 PC104+ PCB.
F
frederick42Aug 25, 2025
How to fix 'Head x check failed' on Z Corporation ZPrinter 650?
- W
  William FoxAug 25, 2025
  If your Z Corporation 3D printer is showing the error 'Head x check failed', it could be due to several reasons. First, make sure the print head is correctly seated and that the contacts are clean by cleaning the print head contacts and Pogo Pins, then reinsert the print heads. If the problem persists, the HP11 Print Head might be old or faulty and require replacement. Another possible cause is a bad carriage cable, in which case you should replace the 50080 Pogo Flex Cable. Additionally, a bad Pogo PCB or a failed PC104+ could be the reason; replace the 50019 Pogo PCB or the 50016 PC104+ PCB, respectively.
J
Jennifer HernandezAug 27, 2025
What causes 'I2C read failed for Head x' on Z Corporation ZPrinter 650?
- J
  jerry35Aug 27, 2025
  If your Z Corporation 3D printer displays the error 'I2C read failed for Head x', it could be due to a few reasons. First, check if the print head is seated properly and ensure the contacts are clean by cleaning the print head contacts and Pogo Pins, then reinsert the print heads. If the problem persists, the HP11 Print Head might be old or faulty and need replacement. Another potential cause is a bad carriage cable, which means you should replace the 50080 Pogo Flex Cable. Also, a bad Pogo PCB could be the issue, requiring you to replace the 50019 Pogo PCB.
D
Daniel WareAug 28, 2025
Why is my Z Corporation 3D Printer displaying 'Head fire voltage stuck'?
- F
  Faith CollinsAug 28, 2025
  If your Z Corporation 3D printer shows the error 'Head fire voltage stuck', it could be due to several reasons. Start by checking the print head and ensuring it is properly seated with clean contacts by cleaning the print head contacts and Pogo Pins, then reinsert the print heads. If the issue continues, the print head may be old or faulty and need replacement. Another possible cause is a bad carriage cable, requiring replacement of the 50080 Pogo Flex Cable. Additionally, a bad Pogo PCB could be the problem, so replace the 50019 Pogo PCB. In some instances, a failed PC104+ may be the cause, needing replacement of the 50016 PC104+ PCB.
C
Cheryl SchmidtAug 30, 2025
What does 'Invalid head temperature' mean on Z Corporation 3D Printers?
- R
  Richard RiveraAug 30, 2025
  If your Z Corporation 3D printer is displaying the error 'Invalid head temperature', several issues could be the cause. Ensure the service station is clean and the squirter block isn't clogged by cleaning the 6 service station squirter block holes or replacing the 30008 squirter block. A worn service station wiper should be replaced with a 30011 Service Station Wiper. Also, make sure the print head is correctly seated and the contacts are clean by cleaning the print head contacts and Pogo Pins, then reinsert the print heads. If the problem continues, the print head may be old or faulty and require replacement. A bad carriage cable or Pogo PCB could also be the cause, requiring replacement of the 50080 Pogo Flex Cable or the 50019 Pogo PCB, respectively.
R
Rebecca FergusonAug 31, 2025
How do I resolve 'AUTOALIGN: can't pick reference head' on Z Corporation ZPrinter 650?
- D
  David JonesAug 31, 2025
  If your Z Corporation 3D printer shows 'AUTOALIGN: can't pick reference head', first ensure the sensor window is clean, and then retry. If the problem continues, perform a fill bed to ensure the build bed is flat. Check for a dirty sensor on the Pogo or oil in the carriage; clean the sensor on the Pogo with alcohol and clean inside the carriage, then retry. Make sure the Pogo Card is correctly aligned and the sensor is snapped in; realign the pogo card if necessary. If problems persist, consider replacing the 50019 Pogo PCB or the 50080 Pogo Flex Cable, as a bad Pogo PCB or carriage cable can cause this issue. A failed PC104+ may also be the cause, needing replacement of the 50016 PC104+ PCB.
M
mercedes20Sep 2, 2025
What causes 'Head x current too high' error on Z Corporation ZPrinter 650?
- J
  Jennifer WilliamsSep 3, 2025
  If your Z Corporation 3D printer displays the error 'Head x current too high', it could be due to several reasons. The print head might be old or faulty, so consider replacing it. Ensure the print head is properly seated and the contacts are clean by cleaning the print head contacts and Pogo Pins, then reinsert the print heads. Additionally, a bad carriage cable or Pogo PCB could be the cause, requiring replacement of the 50080 Pogo Flex Cable or the 50019 Pogo PCB, respectively. In some cases, a failed PC104+ PCB may be the cause, needing replacement of the 50016 PC104+ PCB.
J
Joshua WalshSep 4, 2025
How do I fix 'AUTOALIGN: alignment of Axis x failed' on my Z Corporation 3D Printer?
- A
  April AustinSep 4, 2025
  If your Z Corporation 3D printer displays 'AUTOALIGN: alignment of Axis x failed', start by cleaning the sensor window and retry. If the issue persists, perform Fill Bed to ensure the build bed is flat. Check for a dirty sensor on the Pogo or oil in the carriage; clean the sensor on the Pogo with alcohol and clean inside the carriage, then retry. Ensure the Pogo Card is correctly aligned and the sensor is snapped in; realign the pogo card if needed. If problems continue, consider replacing the 50019 Pogo PCB or the 50080 Pogo Flex Cable, as a bad Pogo PCB or carriage cable can cause this issue.
L
lori53Sep 6, 2025
What should I do if my Z Corporation 3D Printer shows 'AUTOALIGN: weak sensor reading'?
- W
  wfitzgeraldSep 6, 2025
  If your Z Corporation 3D printer is showing the error 'AUTOALIGN: weak sensor reading', start by cleaning the window and retry. If the issue persists, perform a fill bed. Check for a dirty sensor on the Pogo or oil in the carriage; clean the sensor on the Pogo with alcohol and clean inside the carriage, then retry. If the pogo card is crooked or the sensor is not snapped in, realign the pogo card. If the problem continues, it may be due to a bad Pogo PCB or carriage cable; replace the 50019 Pogo PCB or the 50080 Pogo Flex Cable accordingly.