Home
Z Corporation
3D Printers
ZPrinter 650
Z Corporation ZPrinter 650 Troubleshooting Guide
68 pages
Manual
Specs
Ask a question
To Next Page
To Next Page
Loading...
09915
ZPrinter
650
Troubleshooting
Guide
ZPrinter
®
650
Troubleshooting
Guide
Part Number 09915
Revision B
1
2
Table of Contents
Preface
3
Notices
5
Symbols
6
Table of Contents
7
Print Head and Pogo Issues: Print Head, Pogo and Alignment Issues
10
1003: I2C Read Failed for Head X
10
1004: Head X Fire Voltage Failed
11
1006: Head X Temperature too High
12
1007: Head X Current too High
13
1009: Head Fire Voltage Stuck
14
1010: Invalid Head Temperature
15
3011: SEQUENCER: Error in DPC, Flags
16
40006: AUTOALIGN: Weak Sensor Reading
17
40007 AUTOALIGN: Alignment of Axis X Failed
18
40008: AUTOALIGN: Can't Pick Reference Head
19
40800: Head X Check Failed
20
60400: FPGA: Comm Error on Pogo Card
21
60501: POGOPOWERSPI: Timed out
22
60502: POGO POWER: Read Error
23
60520: HP11 COMMANDSPI: Timed out
24
10040: POGOSTATUSSPI: Timed out
24
Motion Errors: Axis Problems
27
2301(0): MOVER: Axis 0 Destination out of Range
27
2303(0): MOVER: Axis 0 Excessive Position Error
28
2303(1): MOVER: Axis 1 Excessive Position Error
29
2305(0): MOVER: Axis 0 Didn't Settle
30
2305(1): MOVER: Axis 1 Didn't Settle
31
2400(0): REZERO: Axis 0 Can't Find End of Travel
32
2400(1): REZERO: Axis 1 Can't Find End of Travel
33
3012: SEQUENCER: Spurious Interrupt
34
3013: SEQUENCER: Timed out Finishing Swath
35
43000: SEQUENCER: Missed Position
36
60300: REZERO: Fast Axis Length out of Tolerance
37
60301: REZERO: Slow Axis Length out of Tolerance
38
Spread Issues: Problems with Spreading Powder Efficiently
40
Spread Not Smooth
40
Feeder Is Not Dispensing Enough Powder (Short Spreading Figure 21)
41
5001: POWDER: no more Feed
42
60100: Feeder Timeout
43
40204: TI: Build Piston Driver Overload
44
Powder Handling: Issues with Depowering, Auto Gross De-Powdering, Vacuum
46
Front/Rear Overflow Is Full or Not Emptying
46
Build Bed will Not Empty
47
No/Light Suction on User Hose
48
De-Powdering Chamber Is Full of Powder While De-Powdering
49
No Compressed Air or Not Enough Compressed Air
49
Powder Is Seeping out of Printer
50
Boot Failure and Inverter Issues: Printer will Not Come Online
51
60200: LOWLEVEL: 15V Supply Voltage out of Tolerance
51
61300: INVERTER: Bad Version Number
51
61301: Timeout Waiting for SPI Bus
52
61302: INVERTER: Comm Error
52
61305: INVERTER: Heater Driver over Temp
52
61308: INVERTER: Line under Voltage
53
Blank Illuminated LCD
53
Net Init Failed
53
Boot Failure: no Power
54
Communication and Software Errors: Errors that Are Caused by Communication and Software Problem
55
Packet Timeout: Printer Not Found: before Printing
55
Packet Timeout: Printer Not Found: While Printing
56
1905: LAYERS: Layer Is too Big
56
3900: SOCKETS: Can't Initialize Winsock Interface
56
Fluids: Fluid Leaks Within the Printer
57
Service Station Is Full of Fluid
57
Binder on Top Deck
57
Binder Leaking from Bottom of Printer
57
Air in Lines
58
Software Says the Binder Reservoir Is Empty
58
Sensors and Switches: Errors that Are Related to the Zprinter's Sensors and Switches
59
Top Cover Open
59
1008: Head Cover Open
59
Heater Is Not Coming up to Temperature
59
Miscellaneous Errors: Errors that Do Not Fall into any Other Category
60
3202: Monitor Thread Took too Long
60
Appendix
61
Appendix A: Cleaning the Alignment Sensor
61
Appendix A: Cleaning the Alignment Sensor (Cont.)
62
Appendix B: Understanding and Troubleshooting the Zprinter 650 Load Cell
63
Other manuals for Z Corporation ZPrinter 650
Hardware Manual
99 pages
Need help?
Do you have a question about the Z Corporation ZPrinter 650 and is the answer not in the manual?
Ask a question
Z Corporation ZPrinter 650 Specifications
General
Brand
Z Corporation
Model
ZPrinter 650
Category
3D Printers
Language
English
Related product manuals
Z Corporation ZPrinter 310
127 pages
Z Corporation Spectrum Z 510
76 pages
Need help?
General
To Next Page
