What to do if my Zanussi Refrigerator does not operate?
If your Zanussi Refrigerator isn't working, there are a few things to check: * Make sure the appliance is switched on. * Ensure the mains plug is correctly connected to the mains socket. * Test the socket by plugging in another electrical appliance to see if there is voltage. If not, contact a qualified electrician.
Why is there too much frost and ice in my Zanussi ZRDN18FS1?
Excessive frost and ice in your Zanussi Refrigerator can be due to several reasons: * The door may not be closed correctly. * Food products may not be wrapped properly; ensure they are well-wrapped. * The temperature might be set incorrectly. In this case, refer to the "Control Panel" chapter. * The appliance may be fully loaded and set to the lowest temperature; try setting a higher temperature. Refer to "Control Panel" chapter. * The temperature set in the appliance may be too low and the ambient temperature too high; set a higher temperature. Refer to "Control Panel" chapter. * The gasket may be deformed or dirty. In this case, refer to "Closing the door" section.
How to reduce noise from my Zanussi ZRDN18FS1?
If your Zanussi Refrigerator is making excessive noise, check if the appliance stands stable. If it does not, adjust it until it stands stable.
Why is water leaking onto the floor from my Zanussi ZRDN18FS1?
If water is leaking onto the floor from your Zanussi Refrigerator, the melting water outlet may not be connected to the evaporative tray above the compressor. Attach the melting water outlet to the evaporative tray.
Why is the temperature too high or too low in my Zanussi ZRDN18FS1?
If the temperature in your Zanussi Refrigerator is not optimal, the temperature may not be set correctly. Try setting a higher or lower temperature.
What to do if water flows inside my Zanussi ZRDN18FS1 Refrigerator?
If you notice water flowing inside your Zanussi Refrigerator: * Ensure that food products do not touch the rear plate, as this can prevent water from flowing into the water collector. * Check if the water outlet is clogged and clean it if necessary.
Why is the lamp not working in my Zanussi ZRDN18FS1?
If the lamp in your Zanussi Refrigerator isn't working, it might be in stand-by mode. Try closing and then opening the door to see if that resolves the issue.
Why can't I set the temperature on my Zanussi ZRDN18FS1?
If you cannot set the temperature on your Zanussi Refrigerator, the "FastCool function" might be switched on. You can either switch off "FastCool function" manually or wait until the function deactivates automatically to set the temperature. Refer to "FastCool function" section.
Why does the compressor in my Zanussi ZRDN18FS1 Refrigerator run constantly?
A constantly running compressor in your Zanussi Refrigerator can be caused by: * Incorrect temperature settings. Refer to the "Control Panel" chapter. * Putting many food products in at the same time. Wait a few hours and then check the temperature again. * High room temperature. Refer to the "Installation" chapter. * Placing warm food products in the appliance. Allow food products to cool to room temperature before storing. * The door not being closed correctly. Refer to "Closing the door" section. * The FastCool function being switched on. Refer to "FastCool function" section.
Why is there condensation on the rear wall of my Zanussi Refrigerator?
Too much condensed water on the rear wall of your Zanussi Refrigerator could be due to: * Opening the door too frequently; try to open the door only when necessary. * The door not being closed completely; ensure the door is fully closed. * Storing unwrapped food; wrap food in suitable packaging before storing it.
General| Energy Efficiency Class | F |
|---|---|
| Cooling System | Static |
| Number of Shelves | 4 |
| Reversible Door | Yes |
| Freezer Position | Bottom |
| Energy Rating | F |
| Noise Level | 39 dB |
| Defrost System | Manual |
| Number of Door Bins | 4 |
| Width | 60 cm |
To Next Page
