Need help?Do you have a question about the Zebex Z-5130 and is the answer not in the manual?
General| Interface | USB, RS-232, Keyboard Wedge |
|---|---|
| Weight | 150 g |
| Drop Test | 1.5 m |
| Resolution | 4 mil |
| Type | Handheld |
| Scan Rate | 100 scans per second |
| Decode Capability | UPC/EAN, Code 39, Code 128, Interleaved 2 of 5, Codabar |
| Operating Voltage | 5V |
| Light Source | 650 nm Laser |
| Depth of Field | 0mm to 200mm |
| Minimum Bar Width | 0.1 mm |
| Print Contrast | 30% @ UPC/EAN 100% |
| Beeper Operation | Programmable tone & volume |
| Power Consumption | 100 mA |
| Operating Temperature | 0°C to 50°C |
| Storage Temperature | -20°C to 60°C |
| Humidity | 5% to 95% (non-condensing) |
| EMC | CE, FCC |
| Scanning Distance | 50 mm - 200 mm |
Identifies and describes the parts of the scanner, including indicators and connectors.
Lists essential safety and placement guidelines for optimal scanner performance.
Details the simple cleaning and maintenance procedures for the scanner window.
Explains the automatic blinking feature for power saving and extended scanner life.
Illustrates the effective reading distance and field for the scanner.
Details how to use the "Test" button to activate scanning when the scanner is in trigger mode.
Explains how to enter and use the performance test mode to evaluate scan results with LED indicators.
Configures beeper behavior and data transmission during performance test mode.
Details RS-45, RS-232, and USB interface connections and their pinouts.
Provides physical dimensions, regulatory compliance, and decode symbology support.
Outlines the step-by-step process for configuring the scanner using programming barcodes.
Lists default settings for scanner operations and interface communication parameters.
Covers symbology selection, code identifiers, length, and data formatting options.
Configures Codabar settings, including start/stop characters, length, and redundant check.
Configures Code 39 settings, including check digit calculation and concatenation.
Configures Code 93 settings, including enable/disable and check digits.
Configures Code 128 settings, including enable/disable, check digits, and concatenation.
Configures Chinese Post Code settings, including enable/disable and check digits.
Configures MSI/Plessy settings, including enable/disable and check digits.
Configures Code 11 settings, including enable/disable and check digit verification.
Configures ITF 2 of 5 settings, including enable/disable and check digits.
Defines maximum, minimum, and fixed length settings for ITF 2 of 5 barcodes.
Configures Standard 2 of 5 settings, including enable/disable and check digits.
Configures Industrial 2 of 5 settings, including enable/disable and check digits.
Configures UPC/EAN/JAN settings, including conversion, add-on options, and check digits.
Configures add-on options for UPC/EAN/JAN, including format and bookland variants.
Manages check digit settings for UPC-A, UPC-E, EAN-13, and EAN-8 barcodes.
Sets mandatory add-on requirements for bookland and Japanese bookland barcodes.
Configures optional add-on requirements for Japanese bookland barcodes.
Configures Telepen settings, including enable/disable and numeric mode.
Configures Matrix 2 of 5 settings, including enable/disable and check digits.
Explains level, edge, and off trigger commands for scanner activation.
Configures system functions like reset, firmware version, and exit modes.
Manages interface configurations, including USB virtual COM, keyboard emulation, and OPOS/JPOS.
Configures beeper tones, volume, and timing for good read and power-on events.
Sets scanner beeper volume and timing for feedback events.
Defines scan modes like trigger, auto scan, and repeat mode for scanner operation.
Reconfigures the behavior of the "Test" button for different operational modes.
Configures power saving modes and blink mode timers for scanner operation.
Sets the delay time between transmitted messages and individual characters.
Sets the delay time for re-reading the same barcode.
Configures RS-232C interface parameters like baud rate, parity, stop bits, handshaking, and terminators.
Sets keyboard terminators like Enter or H-TAB for keyboard emulation.
Configures the speed and narrow/wide ratio for wand emulation.
Configures GS1 DataBar Omnidirectional settings, including check digit and application ID transmission.
Configures GS1 DataBar Limited settings, including check digit and application ID transmission.
Configures GS1 DataBar Expanded settings, including check digit and application ID transmission.
Manages identifier codes for barcodes, enabling/disabling them and setting code tables.
Specifies identifier code settings for various symbologies like Codabar, Code 128, and GS1 DataBar.
To Next Page
