Why does my Zephyr Ventilation Hood turn on by itself?
If your Zephyr Ventilation Hood turns on by itself, it may be because a spotlight or kitchen lamp is shining directly onto the switch controls. The switch controls are light sensitive, and a direct light source may disrupt their function.
What to do if my Zephyr Hurricane AK2500BS Ventilation Hood is not venting out properly?
If your Zephyr Ventilation Hood isn't venting out properly, several factors could be the cause. Ensure you're using solid, rigid metal ducting, as flexible ducting can significantly reduce airflow. Check that the hood is positioned correctly, maintaining a distance between 24” and 32” from the cooktop. Eliminate any external wind by closing nearby windows and doors. Finally, inspect the ductwork and opening for any blockages.
Why is my Zephyr Ventilation Hood not working after installation?
If your Zephyr Ventilation Hood isn't working after installation, start by ensuring that the circuit breaker and the unit's power are turned ON. Then, check the power connection to confirm it's properly connected. Also, verify that the wirings at the switch board and control board are securely connected. If the issue persists, the switch board or control board might be defective and require replacement.
What to do if my Zephyr Ventilation Hood light works, but the blower isn't turning?
If the light on your Zephyr Ventilation Hood is working, but the blower isn't turning, there are several potential causes. First, check the blower cable to ensure it is properly connected. Next, inspect the motor for any debris or obstructions that may be preventing it from turning. If those aren't the issue, the motor or capacitor may be defective and require replacement. Finally, the switch board or control board could be defective, requiring you to change the defective part.
What to do if the blower is working, but the lights are not on my Zephyr Hurricane AK2500BS Ventilation Hood?
If the blower in your Zephyr Ventilation Hood is working, but the lights are not, start by checking the LED light connector to ensure it is properly connected. If the connection is secure, the LED light itself may be defective and need replacing. Finally, the switch board or control board could be defective, requiring replacement.
Why is my Zephyr Ventilation Hood vibrating?
If your Zephyr Ventilation Hood is vibrating, it could be due to a few reasons. Check that the blower is securely tightened in place. Another cause may be a damaged blower wheel, which would need to be replaced. Also ensure that the hood itself is properly secured in place by verifying its installation.
How to fix a vibrating safety grille on my Zephyr Ventilation Hood?
If the safety grille on your Zephyr Ventilation Hood is vibrating, it is likely because the safety grille is loose. To resolve this, simply tighten the safety grille screw.
General safety precautions and warnings for operation and maintenance.
Instructions and precautions for operating the range hood.
Details on electrical supply, codes, and grounding for installation.
Lists all components included with the range hood.
Lists components that must be purchased separately for installation.
Worksheet to calculate total duct length for optimal airflow.
Guidelines for proper hood placement and duct connection distances.
Details various ducting configurations and connection methods.
Technical dimensions and details for the AK21 model.
Technical dimensions and details for the AK25 model.
Technical dimensions and details for the AK65 model.
Information on power requirements, wiring, and grounding.
Guidance on installing a cable locking connector if required by local codes.
Steps to prepare the hood for vertical rectangular ducting.
Steps to prepare the hood for horizontal rectangular ducting.
Illustrates the process of physically attaching the hood to the cabinet.
Explains the touch controls and functions of the AK21 model.
Details the electronic touch controls and features of the AK25 model.
Describes the mechanical slide controls and functions of the AK65 model.
Instructions for cleaning the hood and its components.
Instructions for replacing LED lights if they fail.
Steps to enable and verify the Airflow Control Technology (ACT) settings.
Step-by-step guide to access the PC board for conversion.
General| Brand | Zephyr |
|---|---|
| Model | Hurricane AK2500BS |
| Category | Ventilation Hood |
| Type | Under Cabinet |
| Airflow | 600 CFM |
| Lighting | LED |
| Finish | Stainless Steel |
| Material | Stainless Steel |
| Number of Speeds | 4 |
| Power Source | Electric |
| Voltage | 120 V |
| Color | Stainless Steel |
| Width | 30 inches |
| Duct Size | 6 inches |
| Control Type | Touch |
| Filter Type | Baffle |
To Next Page