Need help?Do you have a question about the ZETRON 4219 and is the answer not in the manual?
Details the rack-mounting procedure for the Model 4048 CCE and its components.
Identifies card slots and types within the Model 4048 CCE, referencing Table 2.
Covers the operation and connection of the Model 4048 Power Supply.
Details card slot types and associations for the Model 4020 CCE, referencing Table 7.
Describes the three types of power supplies available for Model 4020 systems.
Details proper earth grounding practices for system protection, ESD, and noise reduction.
Explains the function of switches for setting data rates and default functions of service ports.
Details how to set CIC switches for console type and cross-mute functionality.
Guides on configuring Dual Channel Cards (DCCs) to meet channel pair requirements.
Explains configuring transmit audio output and receive audio input for low or high impedance.
Describes how to configure cross-busy input to mute channel audio to console positions.
Details how to configure channels to allow or inhibit transmission on a “Busy” channel.
Describes configuring channels for full duplex or simplex operation.
Details basic operating modes and optional features of Universal and Tone/Local DCCs configured via serial port.
Explains how to assign a channel type, including Tone-std and Tone-Custom options.
Details how to define the channel's Call input source, including VOX, COR, and LLGT options.
Details two methods for configuring detection: VOX+COR or VOX+LLGT.
Explains the radio channel interface using DCCs and 50-conductor plugs for connections.
Details electrical specifications for outputs, optically isolated inputs, non-isolated inputs, and IRIG B decoder.
Details the switch settings for assigning card addresses to Auxiliary I/O cards.
Explains how Console Interface Cards (CIC) interface dispatch consoles and details signal summaries.
Outlines diagnostic tests and adjustments for the phone coupler, including primary modes and test procedures.
Details the procedure for testing and adjusting Transmit Audio Gain.
Provides steps to reconfigure the modem if it is no longer configured or needs replacement.
Explains how to access and configure port features for logger, backplane monitor, and radio system management.
Provides instructions for interfacing the Series 4000 with MAP27 radios via Model 4217B or 4219 consoles.
Details the configuration of the MAP27 Dual Channel Control Card using DIP switches.
Explains CCE interconnects for MAP27 Wireless Control Card using punchdown blocks.
Guides on configuring the Orion Dual Channel Wireless Control Card, including DIP switch settings.
Discusses desktop console placement considerations, including space, power, and proximity to CCE.
Discusses rackmount console placement, considering rack space, accessories, and proximity to CCE.
Covers primary power requirements for consoles, including voltage and current specifications.
Details jumper-selectable configuration options and default factory settings for consoles.
Guides on configuring Model 4115B Console Expanders, including setting loop address jumpers.
Describes wiring accessory items to the console, including connectors for power, CCE, and accessories.
Guides on turning on the system power and checking initial LED status indicators.
Details adjusting audio levels on the dual channel card for transmit and receive signals.
Guides on adjusting microphone levels to eliminate background noise and optimize voice clarity.
Explains the MIC-LVL adjustment on the CIC card to compensate for audio losses from a console.
Describes adjusting monitor audio levels for 4-wire and 2-wire channels.
Guides on adjusting auxiliary audio input levels for notch-filtered transmission.
Guides on adjusting receive audio calibration levels at the DCC to the minimum expected audio signal.
Guides on adjusting microphone levels using potentiometers on console boards.
Provides steps for precise microphone level adjustments using alert tones and CIC mic test points.
Provides instructions for installing CPSW software.
Guides on uninstalling CPSW using the standard Windows procedure.
Maps out menu items in CPSW, excluding key definitions.
Continues the mapping of menu items in CPSW.
Provides step-by-step procedures for configuring dispatch consoles using CPSW.
Guides on starting the CPSW application by double-clicking its shortcut.
Explains the serial port setting configuration for the CPSW application.
Explains how to load configurations from a console or a disk file into CPSW.
Provides instructions for receiving configuration from a console using specific cables.
Explains how to edit configuration settings, including system and position configurations.
Describes system-wide settings that affect all positions.
Guides on configuring channels, including naming and selecting channel types.
Guides on assigning and configuring paging formats for leading digits.
Provides steps to configure custom calls, including call number, frequency, and duration.
Guides on configuring position settings, including position number, layout, and panel configurations.
Guides on sending configuration files from a PC to consoles via serial port.
Provides steps for upgrading configuration files to newer IntegratorRD versions.
Guides on creating a console configuration consisting of several files.
Explains how to define radio channels, card types, and channel specifications.
Covers system-specific definitions, including auxiliary I/O, alarm functions, cross muting, and system parameters.
Explains the process of duplicating console configuration data between positions.
Guides on saving the configuration file to disk.
Provides instructions for installing the Radio System Management Program (RSMP).
Outlines steps for performing installation verification on a Series 4000 system.
General| Brand | ZETRON |
|---|---|
| Model | 4219 |
| Category | Control Systems |
| Language | English |
To Next Page
