Zodiac Vortex AV 350 50

Questions and Answers

T
Teresa HillAug 21, 2025
What to do if Zodiac Swimming Pool Vacuum does not stay on the pool bottom?
- J
  John FernandezAug 21, 2025
  If your Zodiac Swimming Pool Vacuum isn't staying firmly on the pool bottom, here are some possible reasons and solutions: * Air may be trapped inside the appliance's casing. Repeat the immersion operations. * The filter might be full or clogged. Clean it with fresh water. If the filter is blocked, clean it with an acid solution (spirit vinegar, for example). Replace the filter if necessary. * The propeller could be damaged.
C
csmithAug 23, 2025
What to do if Zodiac Vortex AV 350 50 Swimming Pool Vacuum does not move on start-up?
- D
  Danielle MartinezAug 25, 2025
  If your Zodiac Swimming Pool Vacuum doesn't move when you start it, verify that the control box's power socket is receiving power and ensure that a cleaning cycle has been initiated and the lights are on.
B
Brandon CordovaAug 26, 2025
What to do if the Zodiac Ultrasonic Jewelry Cleaner control box does not respond?
- Q
  qdunnAug 26, 2025
  If your Zodiac Ultrasonic Jewelry Cleaner control box isn't responding, try unplugging the power cord from the mains socket, waiting 10 seconds, and then plugging it back in.
E
Eric CruzAug 28, 2025
How to fix if part of the pool is not correctly cleaned by Zodiac Ultrasonic Jewelry Cleaner?
- M
  Mr. Robert Chapman MDAug 28, 2025
  To address this issue with your Zodiac Ultrasonic Jewelry Cleaner, repeat the immersion steps, and try different locations in the pool until you find the right spot.
S
Sandra DunnAug 30, 2025
How to prevent Zodiac Vortex AV 350 50 cable from tangling?
- P
  Patty BautistaAug 30, 2025
  To prevent your Zodiac Swimming Pool Vacuum cable from tangling, avoid unrolling the entire length of the cable into the pool. Place only the necessary cable length in the pool and spread the remainder along the pool's edge.
A
Alexis FernandezSep 1, 2025
What to do if Zodiac Swimming Pool Vacuum discharge nozzles are blocked?
- R
  Richard ClarkSep 1, 2025
  If your Zodiac Swimming Pool Vacuum's discharge nozzles or bottom plug holes become blocked, stop the filter pump and start a new cleaning cycle. Also, position the control box halfway along the pool's length, following safety guidelines. If cleaning remains suboptimal, try adjusting the locations of the control box and the point where the cleaner enters the pool.
E
erinwheelerSep 3, 2025
How to improve cleaning if Zodiac Swimming Pool Vacuum doesn't clean part of the pool?
- K
  kelseyjonesSep 3, 2025
  To address incomplete cleaning with your Zodiac Swimming Pool Vacuum, repeat the immersion steps, experimenting with different immersion locations until you find the optimal spot in the pool.
K
Kimberly BlackSep 5, 2025
What to do if Zodiac Vortex AV 350 50 control box does not respond?
- J
  Jason MccoySep 5, 2025
  If the control box for your Zodiac Swimming Pool Vacuum isn't responding, unplug the power cord from the mains socket, wait 10 seconds, and then plug it back in.
J
Jessica MorseSep 7, 2025
Why Zodiac Vortex AV 350 50 Swimming Pool Vacuum climbs the walls erratically?
- C
  Chad YoungSep 8, 2025
  The cleaner may behave differently depending on the lining of the pool. A parameter may require changing. To do this, contact your retailer.
T
Tyler BartonSep 10, 2025
Why Zodiac Ultrasonic Jewelry Cleaner does not climb pool sides?
- J
  John HardySep 10, 2025
  If your Zodiac Ultrasonic Jewelry Cleaner isn't climbing the pool sides as well as it used to, it could be due to several reasons. The filter might be full or clogged, so try cleaning it with fresh water. If it's severely blocked, use an acid solution like spirit vinegar. Replace the filter if necessary. Also, check if the tires are worn and replace them if needed. Microscopic algae may be present, requiring shock chlorination and a slight reduction in pH, but remove the appliance during shock treatment. Finally, inspect the brushes for wear and replace them if necessary.