ZTW Beast User Manual

200A 300A
90*55*50 116*78*74
6.0V/7.4V
Adjustable/8A
6.0V/7.4V
Adjustable/8A
8-24NC/3-8Lipo 18-36NC/6-12Lipo
1/5th Buggy/Truck 1/5th Buggy/Truck
Beast SLL
Beast Pro
● Enhanced throttle response, excellent acceleration, linearity and driveability.
● Beast Pro and Beast series use the advanced PC interface allows you to set up, program or update the
firmware.
● Fully programmable via program card .
● Strong and Adjustable BEC output .
● Multiple protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss
protection.
When using a Sensorless Brushless motor, the Blue motor wire (A), Yellow motor wire (B) and Orange motor
wire (C) of the ESC must be connected with the Sensorless motor wire terminals (A,B,C) respectively.
Do not change the sequence of the wires.
Note: If the motor operates in reverse rotation, this can be changed in the programming settings.
Features
Sensorless Mode
Connection to Rx
LED Indication
Throttle Range Calibration
Function
LED
LED Status
Low voltage of the battery
Red LED
Blinking
Over-heat of the ESC and motor(95℃)
Blue LED Blinking
Sensored Mode
Red and Blue LED
ON
Sensorless Mode
Blue LED
ON
White wire RX-Signal
Red wire RX+6.0V
Black wire RX-
Specification
Sensored Mode
When using a Sensored Brushless motor, the Blue motor wire (A), Yellow motor wire (B) and Orange
motor wire (C) of the ESC must be connected with the Sensored motor wire terminals (A,B,C) respectively.
It is necessary to connect the Sensor wire to the “Sensor” socket on the ESC. Do not change the sequence
of the wires.
Series
Items
Size(LxWxH)mm
BEC
Battery NiXX/Lipo
Suitable Car
Splash
Full
Sensored
Sensorless
Beast
45A 、60A 80A 、120A 120A 、150A
45*32*37/52* 36* 38
52*38*36
55*48*37
6V/2A 6V/3A
6.0V,8.4V
adjustable/3A
5-10NC/ 2-3Lipo 5-12NC/ 2-4Lipo
Program
Card
Waterproof
5-18NC/ 2-6Lipo
LED
LCD
1/10th
Buggy/Truck
1/10th
Buggy/Truck
1/8th
Buggy/Truck
Beast SLL
45A 、 60A
41*33*35
6V/2A
5-10NC/ 2-3Lipo
RTR-1/10th
Buggy/Truck
Beast Pro
120A Turbo
220A
38.1*36.4*31
55*40*34
6V/5A
6.0V/7.4V
Adjustable/8A
5-10NC/ 2-3Lipo 8-18NC/3-6Lipo
1/10th Touring
1/8th Touring/
Buggy/ Truck Racing
Quick Guide
CAR ESC CAR ESC CAR ESC
Beast
The red off
blue on solid
Release the switch
Blue led blink for
3 seconds then go
on solid,motor
“~beep~beep~”
Release trigger to
neutral position
Hold the switch The red and blue
are on solid
2 Seconds
Push trigger to
full brake
Red led blink for
3 seconds then go
on solid,motor
“~beep~”
Red,blue Led blink
for 1 second then go solid,
motor“~beep~beep~beep~”
Step one
Pull trigger to
full throttle
Step three
Holding the “Switch” button over
2 seconds will turn off the ESC
Step two
SET
OFF
SE
T
O
FF
S
ET
OFF
OR OR
OR
Hold the “set”button,
then turn on the ESC.
Release the
“set”button
Turn off the”ESC”
Remarks:
1.Some of the ESCs have two signal cables : The longer one is for receiver , the shorter
one is for program card.
2.The switch of 200A、300A is different with the other ESC.
CH: HRC Distribution GmbH, 4132 Muttenz
EU: Hartweg R/C, 79540 Lörrach
E-mail: info@hrcdistribution.com
More Manuals:
hrcdistribution.com

ZTW Beast Specifications

General

Brand	ZTW
Model	Beast
Category	Motorized Toy Car
Language	English