ZyXEL Communications G-570U User Manual (English)

Other manuals for ZyXEL Communications G-570U

User Guide162 pages

Declaration Of Conformity1 page

Questions and Answers:

J
Judith RodriguezAug 16, 2025
What to do if I cannot ping any computer on the LAN using ZyXEL Communications Wireless Access Point?
- D
  David StephensAug 16, 2025
  If the ETHN LED on the front panel is off, check the Ethernet cable connections between your ZyXEL Communications Wireless Access Point and the Ethernet device. Also, check the Ethernet cable connections between the Ethernet device and the LAN computers. Look for faulty Ethernet cables. Ensure the LAN computer’s Ethernet adapter is properly installed and working. Verify that the IP address and the subnet mask of the Wireless Access Point, the Ethernet device, and the LAN computers are on the same subnet.
K
Katelyn ByrdAug 20, 2025
What to do if I cannot access the ZyXEL Communications Wireless Access Point from the LAN?
- J
  Jasmin JonesAug 20, 2025
  If the ETHN LED on the front panel is off, check the Ethernet cable connection between your ZyXEL Communications Wireless Access Point and the Ethernet device connected to the ETHERNET port. Check for faulty Ethernet cables. Make sure your computer’s Ethernet adapter is installed and working properly. Check the IP address of the Ethernet device. Verify that the IP address and the subnet mask of the Wireless Access Point, the Ethernet device and your computer are on the same subnet.
M
Michael CastilloAug 25, 2025
What to do if I cannot ping any computer on the WLAN using ZyXEL Communications Wireless Access Point?
- S
  stephanie57Aug 25, 2025
  To resolve this, ensure the wireless adapter on the wireless station is functioning correctly. Verify that both the ZyXEL Communications Wireless Access Point and your wireless station are configured with the same ESSID, channel, and security settings.
M
Miguel KramerAug 27, 2025
What to do if I cannot access the ZyXEL Communications Wireless Access Point from the WLAN?
- J
  Jessica DiazAug 27, 2025
  To fix this, ensure the wireless adapter on the wireless station is working correctly. Check that both the ZyXEL Communications Wireless Access Point and your wireless station are using the same ESSID, channel and security settings.
K
Kenneth MedinaAug 31, 2025
What to do if I cannot connect to an access point when setting up OTIST on ZyXEL Communications Wireless Access Point?
- C
  chrishessAug 31, 2025
  If the LEDs continue to flash, the ZyXEL Communications Wireless Access Point has not made a connection. Make sure that OTIST is set up correctly on both the AP and the Wireless Access Point. All settings must be the same on both devices. Ensure that the AP and the Wireless Access Point are not receiving radio signal interference and are within range. Move the devices closer together and away from any sources of interference, such as microwave ovens, Bluetooth devices and other radio transmitters. Restart OTIST on both devices.
D
David SpencerSep 3, 2025
Why does ZyXEL Communications Wireless Access Point reboot automatically sometimes?
- S
  Shawn BaileySep 4, 2025
  The supplied power to the ZyXEL Communications Wireless Access Point is too low. Check that the Wireless Access Point is receiving enough power. Make sure the power source is working properly.
K
Katie RamseySep 8, 2025
How to fix the issue when none of the LEDs turn on after plugging in the power adapter in ZyXEL Communications Wireless Access Point?
- J
  Julia MannSep 8, 2025
  Make sure you are using the supplied power adapter and that it is plugged in to an appropriate power source. Check that the power source is turned on. If the problem persists, you may have a hardware problem. In this case, you should contact your local vendor.

ZyXEL Communications G-570U Specifications

General

Device Type	Wireless Access Point
Manufacturer	ZyXEL Communications
Model	G-570U
Wireless Standard	802.11g
Frequency Band	2.4 GHz
Maximum Data Rate	54 Mbps
Security	WEP, WPA, WPA2
Interface	Ethernet
Antenna Type	External
Ports	1 x 10/100Mbps Ethernet port