7-1
ITEM CWS100ME
CWS100MEJ
CWS100MECJ
CWS150ME
CWS150MEJ
CWS150MECJ
CWS200ME
CWS200MEJ
CWS200MECJ
CWS300ME
CWS300MEJ
CWS300MECJ
Nominal Media Volume, Ft
3
1.0 1.5 2.0 3.0
Salt Dosage, Lbs.
Salt Effi cient Setting 4 6 8 18
Factory Setting 6 9 12 18
Maximum Setting 16 16 24 45*
Softening Capacity, grains
At Salt Effi cient Setting 16,300 24,200 34,100 67,600
At Factory Salt Setting 21,600 32,000 45,000 67,600
At Maximum Salt Setting 29,000 43,000 56,800 87,800
Salt Effi ciency, grains per lb. of salt
At Salt Effi cient Setting 4,078 4,026 4,260 3.753
Flow Rates
Continuous (no duration limit) 4.0 6.0 7.0 9.0
At 15 psi Pressure Loss 11.0 14.3 13.5 18.5
Pressure Loss, psi
At Continuous Flow 4554
Regeneration Flow Rates, gpm
Backwash 1.7 2.7 2.7 5.3
Brine Draw @ 50 psi 0.18 0.26 0.26 0.45
Slow Rinse @ 50 psi 0.27 0.34 0.36 0.71
Rapid Rinse 1.7 2.7 2.7 5.3
Brine Refi ll 0.5 0.5 0.5 0.5
Approximate Water Used (at Factory Setting) 44 77 78 148
Regeneration Duration, minutes a (at Factory Setting)
1st Backwash 6666
Brine Draw/Rinse 45 45 45 45
2nd Backwash 3333
Rapid Rinse 3333
Brine Refi ll 3’ 51” 3’ 51” 7’ 52” 7’ 52”
Approximate Total Time 61 63 65 69
Inlet/Outlet Size 1” NPT 1” NPT 1” NPT 1” NPT
Mineral Tank Dia. x Ht., in. 8 x 44 10 x 44 10 x 54 14 x 65
Overall D & H w/Valve, in.
Width (Including Brine Tank) 33 35 35 42
Depth 15 15 15 18
Height (Including Valve) 53 53 63 74
Brine Tank, W x D x H, in. 15 x 15 x 34 15 x 15 x 34 15 x 15 x 34 18 x 33
Salt settings below 6# require removal of the salt grid
Salt settings above 24# require optional 18 x 33 brine tank
*Salt settings above 35# require optional 24 x 50 brine tank
Brine Tank Capacity
With Salt Grid Leg Extensions 180 180 180 300
With Salt Grid Leg Extensions
(required on salt settings above 18 #) NA 135 135 300
Approximate Shipping Wt. 97 125 154 244
These softeners conform to NSF/ANSI Standard 44 for specifi c performance claims. When set at the Salt Effi cient setting, these softeners meet or exceed Std. 44 requirement for salt effi ciency. Effi ciency claim is only
valid at the Salt Effi cient Setting.
NOTES: For satisfactory performance, indicated fl ow rates and duration should not be exceeded. Flow rates specifi ed are adequate for normal residential applications. Do not use Service Flow Rate if treated water is to
supply a geothermal heat pump, swimming pool, etc. (contact our Customer Service Department at 1-866-990-9785 before selecting equipment). Service fl ow rates have been tested against NSF Standard 44.
SECTION 7: SPECIFICATIONS AND OPERATING DATA
To Next Page
Loading...
