3M Protecta Cabloc User Manual

6
FORWORD
This instruction manual describes the use and maintenance of the Cabloc Vertical Cable Safety System and Cabloc Detachable
Cable Sleeve. It should be used as part of an employee training program as required by CE and must be kept with the
equipment.
; Installers must read and follow the manufacturer’s instructions for safety equipment used with this system.
; Follow these instructions for proper use, inspection, and maintenance of this equipment before installing this equipment.
; If this product is resold outside the original country of destination, the reseller must provide these instructions in the
language of the country in which the product will be used.
; Before using this equipment, fi nd the product identifi cation information on the installation and service label and record it in
the Inspection & Maintenance Log in this manual.
; Sleeve and system must be inspected after a fall. If the energy absorber/fall indicator on the sleeve is deployed (Figure 15,
example 2), the sleeve must be removed from service. If there are any nicks or kinks in the ladder cable, the cable must be
inspected by a competent person prior to use.
GLOSSARY REFERENCES
Numbered Glossary References on the front cover of this instruction reference the following items:
1
User Instructions.
6
Rigid anchor line, including Detachable Cable Sleeve,
maximum number of system users.
2
Cabloc Vertical Cable Safety Systems
7
Minimum user weight, excluding tools and equipment,
is 40 kg (88 lbs) and maximum user weight, including
tools and equipment, is 140 kg (310 lbs).
3
Standards.
8
Read User Instructions.
4
Number of notifi ed body that performed CE test.
9
Warning symbol.
5
Number of notifi ed body checking the manufacture of this PPE.
1.0 APPLICATIONS
1.1 PURPOSE: Cabloc Vertical Cable Safety Systems (Figure 1) are designed to protect a worker in the event of a fall while
climbing fi xed ladders or similar climbing structures. The
Cabloc Detachable Cable Sleeve (Figures 1 and 2) attaches to
a Cabloc Vertical Cable Safety System. The sleeve is designed to arrest the fall of a worker in the event of a fall while
climbing a fi xed ladder. The Cabloc
Detachable Cable Sleeve is not intended to be used for material handling. Use only
for intended purpose.
Cabloc Detachable Cable Sleeve models covered by this instruction:
Part Number Standard Description
6180200 CE (EN353-1:2014+A1:2017) Cabloc Detachable Cable Sleeve with ZP Carabiner
6180201 CE (EN353-1:2014+A1:2017) Cabloc Detachable Cable Sleeve with SS Carabiner
Cabloc Systems that use the Cabloc Detachable Cable Sleeve:
System Instruction Number System Type System Description
5903940 Vertical Cabloc Vertical Cable Safety System
Cabloc Vertical Cable Safety System Components, Figure 1
A Top Bracket D Cable Guide G Frontal D-Ring
B Cable E System Tag H Full Body Harness
C Cable Sleeve F Bottom Bracket
Cabloc Detachable Cable Sleeve Components, Figure 2 (“i” is Back of Sleeve, “ii” is Front of Sleeve)
A
Cable (not component)
D Handle/Energy Absorber/Fall Indicator G Release Pin J Carabiner
B
Anti-Inversion Pawl
E Sleeve Body, Front H Upper Cam K ID Label
C
Sleeve Body Back
F Front Label I This way UP Arrow
Cable types approved for use with the Cabloc Detachable Cable Sleeve
Cable Part Number DESCRIPTION
AC300SXX Cable, 8mm 7 x 19 Stainless Steel Cable by length.
AC300GXX Cable, 8mm 6 x 19 Galvanized Steel Cable by length.
1.2 LIMITATIONS: The Cabloc Detachable Cable Sleeve must be used with a 3M Fall Protection approved ladder safety
system. Use only a 8 mm (5/16 inch) diameter solid core cable with the Detachable Cable Sleeve. The ladder safety
system must have a maximum angle of 15° from vertical. The ladder safety system may be confi gured with or without
a top, in-line energy absorber. Both confi gurations have been tested and approved for use with the Cabloc Detachable
Cable Sleeve.
EN

3M Protecta Cabloc Specifications

General

Brand	3M
Model	Protecta Cabloc
Category	Safety Equipment
Language	English