ABB A155-M Series - Page 193

Operation Manual / A150-M56/66/57/67 - A155-M..
Figures
© Copyright 2021 ABB. All rights reserved. HZTL4032_EN Revision Q January 2021
Fig.61: Removing cartridge group 3 ...................... 109
Fig.62: Installing the cartridge group on the service
support.......................................................................... 110
Fig.63: Removing the nozzle ring ............................ 111
Fig.64: Measuring clearance A and B...................... 112
Fig.65: Nozzle ring compression PD....................... 113
Fig.66: Installing the nozzle ring.............................. 114
Fig.67: Lifting the cartridge group and rotating it by
90° .................................................................................. 115
Fig.68: Turning the cartridge group....................... 116
Fig.69: Installing the cartridge group .................... 117
Fig.70: Fitting the wall insert and the diffuser..... 118
Fig.71: Installing the compressor casing ............... 119
Fig.72: Turning the cartridge group with com-
pressor and turbine casing ...................................... 120
Fig.73: Installing the gas outlet flange................... 121
Fig.74: Measuring clearances N and R.................... 122
Fig.75: Fitting the insulation.................................... 123
Fig.76: Installing the cartridge group with com-
pressor and turbine casing ....................................... 124
Fig.77: Installing the cartridge group with com-
pressor and turbine casing ....................................... 124
Fig.78: Fitting gas outlet casing without support......
125
Fig.79: Installing gas outlet casing with support 1.....
126
Fig.80: Installing gas outlet casing with support 2....
127
Fig.81: Installing the air inlets.................................. 128
Fig.82: Installing the uncoupled filter silencer ..... 129
Fig.83: Removing the air inlets ............................... 130
Fig.84: Removing the uncoupled filter silencer.... 131
Fig.85: Removing the compressor casing ............. 132
Fig.86: Pressing off compressor casing ................ 133
Fig.87: Remove the diffuser ..................................... 133
Fig.88: Dismantling the diffuser and the wall insert..
134
Fig.89: Removing insulation sheets........................ 135
Fig.90: Removing cartridge group1 ....................... 135
Fig.91: Removing cartridge group 2........................ 136
Fig.92: Removing cartridge group 2 ........................ 137
Fig.93: S_05180 ........................................................... 138
Fig.94: Measuring clearance A and B ...................... 139
Fig.95: Nozzle ring compression PD ....................... 140
Fig.96: Installing the nozzle ring............................... 141
Fig.97: Installing the cartridge group 1 .................. 142
Fig.98: Installing the cartridge group 2.................. 143
Fig.99: Fitting the wall insert and the diffuser..... 144
Fig.100: Installing the compressor casing............. 145
Fig.101: Measuring clearances N and R .................. 146
Fig.102: Fitting the insulation .................................. 147
Fig.103: Installing the air inlets ................................ 148
Fig.104: Installing the uncoupled filter silencer.... 149
Fig.105: Customer tool .............................................. 150
Fig.106: Customer tool .............................................. 150
Fig.107: Positioning the collection tub.................... 151
Fig.108: Removing the fastening strips .................. 151
Fig.109: Fitting the upper fastening strips ........... 152
Fig.110: Fitting the bottom fastening strip........... 152
Fig.111: Fitting the bottom fastening strip ........... 153
Fig.112: Fitting the cartridge group ........................ 154
Fig.113: Positioning the fastening strip ................. 155
Fig.114: Clamping piece............................................. 156
Fig.115: Attach nut...................................................... 157
Fig.116: Initial situation ............................................. 158
Fig.117: Disassembly of the elbows......................... 158
Fig.118: Disassembly of the elbows ........................ 159
Fig.119: Pipe disassembly ......................................... 159
Fig.120: Disassembly of the connecting pieces.... 160
Fig.121: Disassembly of the cleaning nozzle.......... 160
Fig.122: Assembly of the cleaning nozzle................ 161
Fig.123: Assembly of the connecting pieces .......... 161
Fig.124: Pipe assembly............................................... 162
Fig.125: Elbow 1 assembly......................................... 162
Page 191 / 194Page 191 / 194