ABB HT841995 - User Manual

130 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Operation Manual

Turbocharging

ABB Turbo Systems Ltd



ABB Turbo Systems Ltd

CH 5401 Baden

Type TPS 48D01 HT841995

n

Mmax

1035 t

Mmax

750

n

Bmax

983 t

Bmax

710

1/s °C

00180 8 50 50

Year 2013

made in Switzerland

Application according to

the Operation Manual

kg

HZTL2410 English

TPS 48D01

Original Operation Manual

Table of Contents

Questions and Answers

A
Anthony JimenezSep 15, 2025
What to do if there is a reduction in speed of ABB Battery Charger?
- V
  Vanessa TylerSep 15, 2025
  If your ABB Battery Charger experiences a reduction in speed, there might be several reasons. It could be due to defects of connected cylinders when pulse charging, which requires contacting the enginebuilder. Another cause might be heavy contamination of the turbine, which requires cleaning. Damaged rotor components or bearing also can cause the problem, and in this case you should contact an ABB Turbocharging Service Station. Finally, defects such as leaks in the exhaust gas pipes or charge air ducts can lead to speed reduction, and these should be repaired.
P
Paige MarquezAug 25, 2025
Is rubbing of rotating parts in ABB HT841995 a problem?
- D
  David HaneyAug 25, 2025
  Rubbing of rotating parts in ABB Industrial Equipment can be normal behavior and not a malfunction. However, if there is any doubt about the extent of rubbing, then an ABB Turbocharging Service Station must be contacted.
O
obrownAug 25, 2025
What to do if rotating parts are rubbing in ABB HT841995?
- J
  Joshua GeorgeAug 26, 2025
  If you suspect rubbing of rotating parts within your ABB Industrial Equipment, and there is any doubt about the extent of rubbing, then an ABB Turbocharging Service Station must be contacted.
A
andersonmatthewAug 26, 2025
What to do if ABB Industrial Equipment has rubbing of rotating parts?
- B
  Beth Patel DDSAug 27, 2025
  If you suspect rubbing of rotating parts in your ABB Industrial Equipment, and you're unsure about the extent of the rubbing, it's best to contact an ABB Turbocharging Service Station. They can perform a dimension check to assess the situation.
J
johnbanksSep 16, 2025
Why is the lubricating oil pressure too low in my ABB Battery Charger?
- L
  Lisa FreySep 17, 2025
  If the lubricating oil pressure is too low in your ABB Battery Charger, it could be due to several reasons. The oil filter might be heavily contaminated, which means it should be cleaned. Another possibility is a defective oil pump in the lubricating system, which needs to be checked or replaced. The manometer display could be wrong, requiring replacement of the manometer. Alternatively, the rotor axial clearance might be too large, which requires contacting an ABB Turbocharging Service Station.
P
Patrick TurnerSep 23, 2025
What to do if ABB Battery Charger has vibrations?
- S
  Scott SnyderSep 23, 2025
  If you're experiencing vibrations with your ABB Battery Charger, it's likely due to rotor unbalance. In this case, you should contact an ABB Turbocharging Service Station.
R
Ronald SmallSep 8, 2025
What causes charge air pressure to be too high in ABB Battery Charger?
- L
  Laurie ScottSep 8, 2025
  If the charge air pressure of your ABB Battery Charger is too high, it could be due to a malfunctioning or poorly adjusted injection system. You should repair it or contact the manufacturer, or correct it.
P
Philip ScottSep 9, 2025
Why ABB Battery Charger makes noises during run-down?
- W
  wrightkarenSep 9, 2025
  If your ABB Battery Charger is experiencing noises during run-down, the turbocharger may be contaminated, requiring cleaning. Alternatively, there may be a damaged bearing, in which case you should contact an ABB Turbocharging Service Station.
J
Jamie HendersonSep 2, 2025
What to do if ABB Battery Charger is surging?
- A
  Angela HuangSep 2, 2025
  If your ABB Battery Charger is experiencing turbocharger surging, the guard in front of the turbocharger may be contaminated or damaged, requiring cleaning or replacement. Alternatively, the filter silencer or diffuser could be contaminated, in which case you should clean it. Another possibility is a contaminated cooler, which would also need cleaning.
R
Ricardo LindseyAug 31, 2025
What to do if ABB Industrial Equipment is vibrating?
- P
  Patricia JohnsonAug 31, 2025
  If your ABB Industrial Equipment is vibrating, it may be due to rotor unbalance. In this situation, contact an ABB Turbocharging Service Station.

ABB HT841995 Specifications

General

MPN	HT841995
Mounting	DIN rail
Protection Degree	IP20
Mechanical Life	20000 cycles
Electrical Life	10000 cycles
Operating Temperature	-25°C to +60°C

Related product manuals