ABB PowerValue 11 RT 6 kVA

Questions and Answers

E
edward22Sep 23, 2025
What does Battery Over Voltage Alarm Code 16 mean on ABB PowerValue 11 RT 6 kVA?
- J
  Jennifer GonzalezSep 23, 2025
  If your ABB UPS displays a Battery Over Voltage Alarm (Code 16), it indicates that the battery voltage is too high. The UPS will turn off the charger until the battery voltage is normal.
M
Margaret FoleyAug 23, 2025
How to fix Site Wiring Fault Alarm Code 04 on ABB PowerValue 11 RT 6 kVA?
- W
  William ChungAug 25, 2025
  The Site Wiring Fault Alarm (Code 04) on your ABB UPS indicates a difference between ground and neutral voltage exceeding 15V, assuming a Grounding Neutral connection is present. Ensure Site Fault detection is enabled in the LCD settings. Reconnect all input wires to resolve this issue.
M
Mark SantosAug 25, 2025
What does Utility Abnormal Alarm Code 02 mean on my ABB PowerValue 11 RT 6 kVA and how to fix it?
- M
  Meghan SanchezAug 26, 2025
  The Utility Abnormal Alarm (Code 02) on your ABB UPS means the input mains are outside the UPS tolerance range. To resolve this, check the input mains condition.
L
Luke HarrisAug 27, 2025
What to do if my ABB PowerValue 11 RT 6 kVA UPS displays a Battery Disconnect Alarm (Code 11)?
- S
  Sarah WilliamsAug 27, 2025
  If your ABB UPS displays a Battery Disconnect Alarm (Code 11), it means the battery voltage is lower than the batteries disconnected level defined for this UPS. This could be due to a blown fuse, an intermittent battery connection, or a disconnected battery cable. Verify that all batteries are properly connected. If the condition persists, contact your service representative.
K
kyliehooverAug 27, 2025
What does it mean when my ABB PowerValue 11 RT 6 kVA shows Heat sink Over Temperature Alarm Code 81?
- R
  Ryan MullinsAug 27, 2025
  The Heat sink Over Temperature Alarm (Code 81) on your ABB UPS indicates that the temperature of the heat sink is too high, suggesting the UPS is overheating. Transfer the UPS to Bypass-mode. If the condition persists, shut down the UPS. Clear vents and remove any heat sources. Allow the UPS to cool. Ensure the airflow around the UPS is not obstructed. Then, restart the UPS.
S
Sharon MaySep 16, 2025
What does Parallel system battery status Alarm Code E6 mean on ABB PowerValue 11 RT 6 kVA UPS?
- M
  marquezdanielSep 16, 2025
  If your ABB UPS shows a Parallel system battery status Alarm (Code E6), it indicates a discrepancy in battery connections within the parallel system, such as UPS1 batteries being connected while UPS2 batteries are disconnected. Check battery connections to resolve this.
B
Bailey FernandezSep 13, 2025
What does Negative power Fault Alarm Code E1 mean on ABB PowerValue 11 RT 6 kVA?
- M
  mary13Sep 13, 2025
  The Negative power Fault Alarm (Code E1) on your ABB UPS in a parallel system indicates that power from one UPS flows from the parallel output into the other UPS (negative power). If the parallel system is in redundant- mode, only the UPS with the failure will transfer to fault-mode without output; other UPS will still support the load. If the parallel system is not redundant and the load cannot be supported by the other UPS, all units in the parallel system will transfer to fault-mode.
K
kimberlyhickmanSep 14, 2025
What does Parallel cable loss Alarm Code E2 mean on ABB PowerValue 11 RT 6 kVA UPS?
- B
  Brandon JacksonSep 15, 2025
  If your ABB UPS displays a Parallel cable loss Alarm (Code E2) in a parallel system, it means the parallel cable is disconnected. Connect the parallel cable.
B
banksjacquelineSep 5, 2025
What does Byp Overload Fault Alarm Code 43 mean on ABB UPS?
- D
  Donna TorresSep 6, 2025
  The Byp Overload Fault Alarm (Code 43) on your ABB UPS indicates that the UPS has cut off the output and transferred to fault-mode because of overload in bypass- mode or HE-mode. Remove some of the load from the UPS.
C
Catherine JacksonSep 3, 2025
What does Inv Over Voltage Alarm Code 32 mean on ABB UPS?
- R
  Rachel BarnesSep 3, 2025
  If your ABB UPS displays an Inv Over Voltage Alarm (Code 32), it means there is an inverter over voltage. The UPS transfers to Bypass-mode if supporting the load.