ABB ReliaGear LV SG E2.2

Questions and Answers

M
Megan WalkerSep 14, 2025
What does 'Ekip Link Bus' mean on ABB ReliaGear LV SG E2.2 Circuit breakers?
- A
  Andrew FletcherSep 15, 2025
  This indicates a fault in Ekip Link module. Check for loss of connection with one or more actors (modules) connected to Link Bus.
C
Charles MccallSep 14, 2025
What does 'Ekip Com Hub' mean on ABB Circuit breakers?
- E
  Emily RileySep 14, 2025
  This is related to a problem of Ekip Com Hub module with: certificates, connected devices, missing Com modules (RTU or with Ethernet connection), API TLS device, Hub events, parser configuration.
N
nicholas08Sep 13, 2025
What does 'Ethernet disconnected' mean on ABB ReliaGear LV SG E2.2 Circuit breakers?
- C
  Carrie NewmanSep 13, 2025
  If you see 'Ethernet disconnected' on your ABB Circuit Breakers, it indicates that there is no external cable connected to one or more Ekip Com modules with an Ethernet connection.
J
Jeff LopezSep 12, 2025
What to do if ABB ReliaGear LV SG E2.2 Circuit breakers show 'Battery low'?
- M
  Michael EvansSep 12, 2025
  If the ABB Circuit Breakers display a 'Battery low' message, you should change the battery. Consult the 1SDH001000R0509 kit sheet for instructions.
B
Brenda SmithSep 12, 2025
How to fix invalid date on ABB ReliaGear LV SG E2.2?
- K
  Kathleen JacksonSep 12, 2025
  If you receive an 'Invalid Date' error on your ABB Circuit Breakers, it means the date and time are incorrect. You can correct this by going to Settings-System-Date and Settings-System-Time to set the correct date and time.
W
William MartinSep 10, 2025
Why does my ABB ReliaGear LV SG E2.2 show a 'Local bus' error?
- R
  robinsonangelaSep 10, 2025
  If you have 'Local Bus' alarm on your ABB Circuit Breakers, it could be due to several reasons. The unit might be on with auxiliary supply, the Local Bus parameter could be enabled without a connection to the modules, or the connection is incorrect, or communication has been lost for more than five seconds. To resolve this, check the connection and powering of modules in the terminal box or externally, and ensure that the connected modules are compatible with Ekip Touch.
T
Tricia CarrAug 25, 2025
Why ABB ReliaGear LV SG E2.2 Circuit breakers fails to react to opening/closing command from Ekip Touch?
- Y
  ygarzaAug 26, 2025
  The ABB Circuit breaker might fail to react to opening/closing command from Ekip Touch because: * The connections or supplies of the opening/closing actuators are not correct. Check connections and supplies. * There is an absence of auxiliary power supply to Ekip Touch. Check supplies and status of Power LEDs. * The Circuit-breaker is in a condition which fails to enable the selected command. Check circuit-breaker documentation and cases that fail to enable command.
S
Sarah FletcherSep 8, 2025
How to troubleshoot ABB ReliaGear LV SG E2.2 when it is not possible to perform the trip test?
- L
  lisascottSep 8, 2025
  If it is not possible to perform the trip test: * Trip coil is not connected properly. Check Trip coil connection and messages on display. * CB trip signal has not been reset. Press the reset pushbutton. * The busbar current is greater than zero. Correct operating condition.
M
Mr. David HughesSep 7, 2025
Why is the language cannot be changed on ABB Circuit breakers?
- M
  milleraprilSep 7, 2025
  The language cannot be changed on your ABB Circuit breakers because: * Trip unit set remotely. Set it in local mode. * The circuit-breaker is not open. Open the circuit-breaker. * One of the possible power supplies is not present. Power the trip unit with Vaux, Ekip T&P or Ekip TT.
D
Dana DicksonSep 6, 2025
What causes ABB ReliaGear LV SG E2.2 PIN error?
- S
  Sherri WilliamsSep 6, 2025
  If you are experiencing a PIN error with your ABB Circuit breakers, it may be because the PIN is wrong or lost. Contact ABB or consult document 1SDH001501R0001.