How to fix no image on Acer P1265?
First, ensure all connections are properly made as described in the "Getting Started" section and that none of the connector pins are bent or broken. Then, check if the projector lamp has been securely installed, consulting the "Replacing the Lamp" section if needed. Finally, make sure the lens door is slid open and the projector is turned on.
How to change the size of the image on Acer P1265 Projector?
Try adjusting the zoom lever on the top of the projector. You can also move the projector closer to or further from the screen. Alternatively, press "MENU" on the remote control or on the control panel, navigate to "Image setting --> Aspect Ratio", and experiment with different settings.
How to adjust focus on Acer P1265 Projector?
Ensure the lens door is slid open. Adjust the focus ring on the projector lens. Confirm that the projection screen is within the required distance of 3.3 to 39.0 feet (1.0 to 11.9 meters) from the projector or 3.3 to 32.9 feet (1.0 to 10.0 meters)(P5370W).
What to do if Acer Projector image is partial on notebook?
Press "RESYNC" on the remote control or control panel. For an incorrectly displayed image, adjust the resolution of your computer. Press the toggle output settings, for example: [Fn]+[F4] for Compaq, [Fn]+[F4] for HP, [Fn]+[F8] for Dell, [Fn]+[F4] for Gateway, [Fn]+[F7] for IBM, [Fn]+[F3] for NEC, [Fn]+[F5] for Toshiba. If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector.
How to reverse image on Acer P1265?
Select "Image --> Projection" on the OSD and adjust the projection direction.
How to fix slanted image on Acer P1265 Projector?
If possible, reposition the projector so that it is centered on the screen. You can also press the "Keystone / " button on the control panel or press the "Keystone / / / " on the remote control until the sides are vertical.
How to fix partial image on Acer P1265 for PC?
First, try pressing "RESYNC" on the remote control or control panel. If the image is still displayed incorrectly, open "My Computer," then the "Control Panel," and double-click the "Display" icon. Go to the "Settings" tab and ensure your display resolution setting is lower than or equal to SXGA (1280 x 1024) for P1165/P1165P, SXGA+ (1400 x 1050) for P1265/ P1265P, or UXGA (1600 x 1200) for P5260i/P5270/ P5280/P5370W series. Click the "Advanced Properties" button. If the problem persists, change the monitor display and verify the resolution setting is within the limits mentioned above. Click the "Change" button under the "Monitor" tab, then "Show all devices". Select "Standard monitor types" and choose the appropriate resolution mode.
Why is my Acer P1265 image stretched on widescreen DVD?
When playing a DVD encoded in anamorphic or 16:9 aspect ratio, you may need to adjust settings. If playing a Letterbox (LBX) format DVD title, change the format to Letterbox (LBX) in the projector OSD. If playing a 4:3 format DVD title, change the format to 4:3 in the projector OSD. If the image is still stretched, adjust the aspect ratio on your DVD player to 16:9 (wide).
Why is my Acer P1265 Projector image flickering?
Try adjusting the "Tracking" to correct the issue. You can find more information in the "Image Setting" section. Also, try changing the display color depth settings on your computer.
How to fix vertical flickering bar on Acer Projector?
Use the "Frequency" setting to make an adjustment. More information can be found in the "Image Setting" section. Also, check and reconfigure the display mode of your graphics card to ensure it is compatible with the projector.
General| Number of colors | 16.78 million colors |
|---|---|
| Projection distance | 1 - 11.9 m |
| Vertical scan range | 56 - 85 Hz |
| Horizontal scan range | 31.5 - 100 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 2000:1 |
| Screen size compatibility | 0.58 - 7.62 \ |
| Projector native resolution | XGA (1024x768) |
| Keystone correction, vertical | ±40 ° |
| Aspect ratio | 4:3, 16:9 |
| RS-232 ports | 1 |
| Dimensions (WxDxH) | 299 x 229 x 93 mm |
| Throw ratio | 1.95 - 2.15:1 |
| Lamp type | P-VIP |
| Lamp power | 180 W |
| Light source type | Lamp |
| Service life of light source | 3000 h |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Noise level | 28 dB |
| Market positioning | Presentation |
Weight and Dimensions| Weight | 3000 g |
|---|
Guides users on connecting various input devices like DVD players and computers.
Details the procedure for turning the projector on and off, including indicator lights.
Covers adjusting image height, size, and distance for optimal viewing.
Provides guidance on achieving optimal image sizes at various distances from the screen.
Explains how to set image size using distance and zoom controls.
Highlights the key technical specifications and capabilities of the Acer projector.
Explains how to navigate and use the projector's OSD menus for adjustments.
Provides solutions for common image-related problems and projector issues.
To Next Page
