Active SE01 - User Manual

Questions and Answers

R
Robert JacksonAug 17, 2025
Why Active Pressure Washer foam blaster is not working?
- J
  James HubbardAug 17, 2025
  If the foam blaster on your Active Pressure Washer isn't working, consider these possibilities: * The detergent container might be empty, so add more detergent. * The detergent bottle or suction tube might not be properly connected; check these connections. * The detergent could be too thick; dilute it. * The filter on the detergent suction tube might be clogged; run warm water through it to remove any build-up. * The detergent suction tube might be damaged or clogged; remove any obstruction or replace the tube.
D
David BairdAug 19, 2025
Why does my Active Pressure Washer motor not start?
- K
  kelleykathleenAug 19, 2025
  The Active Pressure Washer motor may not start for several reasons. First, check if the device is in OFF mode and push the ON/OFF button to turn it ON. Ensure the power cord is properly plugged in. If you're using an extension cord, it might be too long, the wrong gauge, or damaged; replace it with a 25’ (7.6 m) or 50’ (15 m) 14/3 gauge cord. The power outlet could also be the issue, so try a different outlet. Finally, the pressure washer circuit breaker might have tripped; allow the device to cool before restarting.
D
Dr. Amber PhillipsAug 22, 2025
What to do if Active Pressure Washer output pressure fluctuates?
- C
  Charles MccallAug 23, 2025
  If the output pressure of your Active Pressure Washer fluctuates, it could be due to several reasons. Ensure you have enough inlet water supply by fully turning on the faucet and checking the garden hose for kinks, leaks, or blockages. Another cause might be the pump sucking air; inspect all hoses and fittings to ensure they are airtight, then turn the device OFF and purge the pump by pulling the trigger on the spray gun until a steady flow of water emerges. Also, the water inlet filter could be clogged, so remove and rinse it with warm water. Finally, the discharge nozzle could be obstructed; blow out or remove any debris with a fine needle. Calcified gun, hose, or power nozzle also can cause this problem, so run distilled vinegar through the detergent container.
S
Sarah OlsonAug 25, 2025
Why is my Active SE01 Pressure Washer pump noisy?
- E
  Erin ReevesAug 26, 2025
  A noisy Active Pressure Washer pump can be caused by a few things. The pump might be sucking air; check that all hoses and fittings are airtight, then turn the device to OFF mode and purge the pump by pulling the trigger on the spray gun until a steady flow of water emerges through the nozzle. Alternatively, the water filter could be clogged; remove it and rinse it with warm water.
F
faithjonesAug 28, 2025
Why Active Pressure Washer does not reach high pressures?
- A
  Anthony BassAug 28, 2025
  If your Active Pressure Washer isn't reaching high pressures, several factors could be responsible. The garden hose might be too small; replace it with a 1” (25 mm) or 5/8” (16 mm) garden hose. A restricted water supply could also be the cause; check the garden hose for kinks, leaks, or blockage. Ensure you have enough water supply by fully opening the water source. The water inlet filter might be clogged; remove the filter and rinse it with warm water. Lastly, the pump could be sucking air; check if all hoses and fittings are airtight and purge the pump by turning the device to OFF mode and pulling the trigger on the spray gun until a steady flow of water emerges through the nozzle.
C
crosbycourtneyAug 30, 2025
What to do if Active SE01 Pressure Washer motor hums but fails to run?
- M
  Michael WilliamsAug 31, 2025
  If your Active Pressure Washer motor hums but doesn't run, it could be due to several reasons. First, verify that only the pressure washer is running on the circuit, as the supply voltage might be below the minimum requirement. The system may also have residual pressure; turn the device to OFF mode, pull the trigger on the spray gun to release pressure, and then turn the device back ON. Voltage loss from an extension cord could also be the issue; unplug any extension cords and plug the unit directly into the outlet. Lastly, residual friction among components might be the cause; disconnect the water supply and power ON for 2 to 3 seconds, repeating this procedure a few times until the motor starts.
M
Mrs. Shelly HaleSep 2, 2025
Why Active Pressure Washer garden hose connection leaks?
- N
  Nicole HintonSep 2, 2025
  If the garden hose connection on your Active Pressure Washer is leaking, it could be due to loose fittings; tighten them. Another possibility is a missing or worn rubber washer; insert a new washer.
E
ethompsonSep 5, 2025
What to do if Active SE01 Pressure Washer spray wand leaks?
- C
  christopher04Sep 5, 2025
  If your Active Pressure Washer spray wand, extension, or nozzle is leaking, make sure the spray nozzle was properly attached. Ensure the quick-connect wand is securely attached and the project tip is clicked in securely. For a broken O-ring or plastic insert, call the Toll-free Hotline.
S
Stacey PierceSep 7, 2025
Why Active SE01 Pressure Washer has no water coming out of the nozzle?
- J
  James AndersonSep 8, 2025
  If no water is coming out of the nozzle of your Active Pressure Washer, first check if the water supply is OFF and turn it ON. Also, inspect the garden hose for any kinks and remove them.
A
annawilsonSep 12, 2025
Why Active SE01 Pressure Washer water leaks from the pump?
- J
  Justin BoothSep 12, 2025
  If water leaks from the pump of your Active Pressure Washer (more than 10 drops per minute), check if all fittings are tight. If the water seals are damaged or worn, call the Toll-free Hotline.