Active VE52 - User Manual

Questions and Answers

E
eric98Sep 9, 2025
Why is the output pressure fluctuating high and low on my Active VE52?
- K
  Kenneth LoveSep 9, 2025
  If the output pressure of your Active Pressure Washer is fluctuating, it could be due to several reasons. There might not be enough inlet water supply, so turn the faucet on fully and check the garden hose for kinks, leaks, or blockages. The pump might be sucking air; check if all hoses and fittings are airtight, turn the device OFF, and purge the pump by pulling the trigger on the spray gun until a steady flow of water emerges through the nozzle. The water inlet filter could be clogged, so remove the filter and rinse it with warm water. The discharge nozzle might be obstructed; blow out or remove debris with a fine needle. Finally, the gun, hose, or power nozzle might be calcified; run distilled vinegar through the detergent container.
C
Christopher RobertsonAug 23, 2025
What to do if the foam blaster is not working on my Active VE52?
- E
  Elizabeth HarveyAug 23, 2025
  If the foam blaster on your Active Pressure Washer isn't working, consider these possibilities: * The detergent container might be empty, so add more detergent. * The detergent bottle or suction tube might not be properly connected, so check the connections. * The detergent might be too thick, so dilute it. * The filter on the detergent suction tube might be clogged; run warm water through the filter to remove build-up. * The detergent suction tube might be damaged or clogged; remove any obstruction or replace the detergent suction tube.
J
Jennifer ParksAug 25, 2025
Why does my Active VE52 motor not start?
- T
  Tyler SmithAug 25, 2025
  The Active Pressure Washer motor may not start for several reasons. First, check if the device is in OFF mode and push the ON/OFF button to turn it ON. Ensure the power cord is properly plugged in. If you're using an extension cord, it might be too long, the wrong gauge, or damaged; replace it with a 25’ (7.6 m) or 50’ (15 m) 14/3 gauge cord. The power outlet could also be the issue, so try a different outlet. Finally, the pressure washer circuit breaker might have tripped; allow the device to cool before restarting.
C
Carrie HarrisAug 26, 2025
What to do if Active VE52 Pressure Washer output pressure fluctuates?
- S
  Stephanie SmithAug 27, 2025
  If the output pressure of your Active Pressure Washer fluctuates, it could be due to several reasons. Ensure you have enough inlet water supply by fully turning on the faucet and checking the garden hose for kinks, leaks, or blockages. Another cause might be the pump sucking air; inspect all hoses and fittings to ensure they are airtight, then turn the device OFF and purge the pump by pulling the trigger on the spray gun until a steady flow of water emerges. Also, the water inlet filter could be clogged, so remove and rinse it with warm water. Finally, the discharge nozzle could be obstructed; blow out or remove any debris with a fine needle. Calcified gun, hose, or power nozzle also can cause this problem, so run distilled vinegar through the detergent container.
S
Sierra BriggsAug 27, 2025
Why is my Active VE52 Pressure Washer pump noisy?
- A
  Ashley Simmons MDAug 28, 2025
  A noisy Active Pressure Washer pump can be caused by a few things. The pump might be sucking air; check that all hoses and fittings are airtight, then turn the device to OFF mode and purge the pump by pulling the trigger on the spray gun until a steady flow of water emerges through the nozzle. Alternatively, the water filter could be clogged; remove it and rinse it with warm water.
K
Katelyn GillAug 29, 2025
Why Active VE52 Pressure Washer does not reach high pressures?
- B
  bishopbenjaminAug 29, 2025
  If your Active Pressure Washer isn't reaching high pressures, several factors could be responsible. The garden hose might be too small; replace it with a 1” (25 mm) or 5/8” (16 mm) garden hose. A restricted water supply could also be the cause; check the garden hose for kinks, leaks, or blockage. Ensure you have enough water supply by fully opening the water source. The water inlet filter might be clogged; remove the filter and rinse it with warm water. Lastly, the pump could be sucking air; check if all hoses and fittings are airtight and purge the pump by turning the device to OFF mode and pulling the trigger on the spray gun until a steady flow of water emerges through the nozzle.
Y
Yolanda ThomasSep 17, 2025
Why is my Active Pressure Washer spray wand, extension, or nozzle leaking?
- A
  Austin McdonaldSep 18, 2025
  A leak in your Active Pressure Washer's spray wand, extension, or nozzle could be because the spray nozzle was not properly attached; ensure the quick-connect wand is attached securely and that the project tip is clicked in securely.
G
Gabriel McdonaldSep 18, 2025
Why is water leaking from the pump of my Active VE52 Pressure Washer?
- J
  Joseph BrownSep 22, 2025
  If water is leaking from the pump of your Active Pressure Washer (up to 10 drops per minute is permissible), it could be due to loose fittings; check if all fittings are tight.
P
Patricia CooperSep 7, 2025
Why Active Pressure Washer oil is dripping?
- T
  Tina AguilarSep 8, 2025
  If oil is dripping from your Active Pressure Washer, it indicates that the oil seals are damaged or worn. In this case, you should call the Toll-free Hotline.
C
Christina SandersSep 4, 2025
Why Active Pressure Washer has no water coming out of the nozzle?
- T
  Thomas MatthewsSep 4, 2025
  If no water is coming out of the nozzle of your Active Pressure Washer, first check if the water supply is OFF and turn it ON. Also, inspect the garden hose for any kinks and remove them.