How to fix ActronAir LM7-2W Controller set-temp that can’t be adjusted?
If you're unable to adjust the set temperature on your ActronAir Controller, and an EXX code is displayed on the wall controller, record the digits following 'E' and contact your installer. Also, ensure you are not exceeding the set-temperature limits on your wall control, and verify that the upper and lower temperature limits are correctly configured.
Why ActronAir LM7-2W 7-day time clock is not accepting times I enter?
If the 7-day time clock on your ActronAir Controller isn't accepting the times you enter, make sure that the times do not overlap with those from another day. Also, ensure you are not trying to set the time past the maximum allowable limit.
Why is the ActronAir Controller cooling/heating not sufficient?
Insufficient cooling or heating in your ActronAir Controller can occur if the return air filter is clogged with dust and dirt. Ensure that the air inlet and outlet on the outdoor unit are not blocked. Also, the outside temperature being above or below the design conditions may affect the cooling/heating function.
What to do if ActronAir LM7-2W system does not start?
If your ActronAir Controller system doesn't start, verify that at least 5 minutes have passed since turning it on, as the system includes built-in safety timers. Also, check that your thermostat settings are correct and that the thermostat set-point is appropriately low for cooling or high for heating.
What to do if air does not flow from ActronAir Controller Indoor Unit?
If air isn't flowing from the indoor unit of your ActronAir Controller, ensure that the zones are switched on, if applicable. Note that during heating, air might not flow for about 15 seconds after startup to prevent cold drafts. Also, during defrosting of the outdoor unit in heating mode, the indoor fan may not operate for several minutes to prevent cold air from being blown into the rooms.
Why is my ActronAir Air Conditioner Accessories cooling/heating not sufficient?
Insufficient cooling or heating in your ActronAir Air Conditioner Accessories might occur if the return air filter is clogged with dust and dirt, hindering effective operation. Additionally, ensure that the air inlet and outlet on the outdoor unit are not obstructed. The outside temperature being above or below the design conditions can also affect performance.
What to do if ActronAir Air Conditioner Accessories system does not start?
If your ActronAir Air Conditioner Accessories system doesn't start, first, verify that at least five minutes have passed since turning it on, as the system incorporates built-in safety timers. Next, check that the thermostat settings are correct. Also, ensure the thermostat set-point is adequately low for cooling or sufficiently high for heating.
How to fix ActronAir Air Conditioner Accessories when set-temp can’t be adjusted?
If you're unable to adjust the set temperature on your ActronAir Air Conditioner Accessories, and an EXX code is displayed on the wall controller, record the digits following 'E' and contact your installer. Also, verify that you are not exceeding the set-temperature limits on your wall control. You should also check that the upper and lower temperature are set correctly.
What to do if air does not flow from ActronAir Air Conditioner Accessories indoor unit?
If air isn't flowing from the indoor unit of your ActronAir Air Conditioner Accessories, check that the zones are switched on, if applicable. During heating, air might not flow for about 15 seconds after startup to prevent cold drafts. Also, during the defrost cycle of the outdoor unit in heating mode, the indoor fan might not operate for several minutes to avoid blowing cold air into rooms.
Why is ActronAir Air Conditioner Accessories 7-day time clock not accepting times?
If the 7-day time clock on your ActronAir Air Conditioner Accessories isn't accepting the times you enter, ensure that you don't have overlapping times from another day. Also, verify that you're not attempting to set the time past the maximum allowable limit.
Restarts the unit in the same mode after a power failure if selected.
Allows installation and operation of up to two wall controllers on one system.
Displays room temperature for 3 seconds upon pressing specific buttons.
Selects sensors based on active zones for optimal comfort control.
Automatically activates defrost mode to prevent frost buildup on the outdoor heat exchanger.
Delays indoor fan in heating mode to warm up the heat exchanger before airflow.
Indicates when the air filter requires cleaning based on accumulated run time.
Detects system faults and displays relevant fault codes on the controller.
Allows setting ON and OFF times for specific events on each day of the week.
Explains the functionality of the 7-day time clock for scheduling operations.
Provides advice for efficient cooling operation during summer months.
Provides advice for efficient heating operation during winter months.
Offers strategies and advice for reducing energy consumption.
General| Compatibility | ActronAir Ducted Systems |
|---|---|
| Display | LCD Touchscreen |
| Power Supply | 24V AC |
| Wireless | No |
| Control Modes | Cool, Heat, Fan, Auto |
| Temperature Range | 16°C to 30°C |
To Next Page
