EasyManua.ls Logo

Adam Equipment HCB 123 - User Manual

Adam Equipment HCB 123
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
© Adam Equipment Company 2016 1
Adam Equipment
HIGHLAND SERIES
(Includes HCB xxxM EU & NTEP approved models)
(HCB Software ver. 2.5 or higher – standard models)
(HCB-M Software. rev 2.38 or higher – EU ap
proved models)
(HCB-aM Software rev. 3.10 or higher – NTEP approved models)
COPY

Table of Contents

Questions and Answers

  • K
    Kendra GreerAug 14, 2025
    What to do if Adam Equipment Scales show Err 4?
    • W
      Whitney TaylorAug 14, 2025
      If your Adam Equipment Scales display 'Err 4', it could be due to several reasons. First, ensure there is no weight on the pan when turning the scale on and that the transit screw is removed and the pan is correctly fitted. Second, if you're zeroing the balance, remove any weight from the stainless steel pan. Also, the balance may need recalibration. There may be damage to the load cell or electronics.
  • W
    Wayne PerryAug 17, 2025
    Why Adam Equipment HCB 123 Scales are unstable and can't get a stable reading?
    • D
      David StephensonAug 17, 2025
      If your Adam Equipment Scales are unstable, it could be due to possible damage to the mechanics or load cell. Ensure the scale is on a flat surface and away from vibration. Also, make sure the calibration weight is in its off position.
  • J
    Jeffrey MillerAug 21, 2025
    Why is the red light on on my Adam Equipment HCB 123 Scales?
    • D
      Deborah TorresAug 21, 2025
      If the red light is on, the internal battery may be flat. Charge the battery or replace the internal rechargeable battery.
  • E
    edwardskathrynAug 25, 2025
    How to fix Adam Equipment Scales with no power when turning on?
    • J
      Jessica ThomasAug 26, 2025
      If there is no power when turning on your Adam Equipment Scales, the internal battery may be flat. Try charging the battery or replacing the internal rechargeable battery.
  • A
    Amy WoodwardAug 28, 2025
    What does Err 9 mean on Adam Equipment HCB 123 Scales and how to resolve it?
    • X
      xkellerAug 29, 2025
      If your Adam Equipment Scales display 'Err 9', the load cell may be damaged. Ensure nothing is touching the pan and that the balance is level, free from air movement, vibration, or instability. Try recalibrating the balance.
  • D
    Dawn FosterSep 1, 2025
    What does Err 6 mean on Adam Equipment HCB 123?
    • M
      Michelle StevensSep 1, 2025
      If your Adam Equipment Scales display 'Err 6', the load cell or electronics may be damaged. Remove any weight from the stainless steel pan and turn the balance off and back on again. Also, try calibrating the balance.
  • A
    Alicia LewisSep 5, 2025
    What to do if Adam Equipment Scales show Err 5?
    • B
      bethany54Sep 5, 2025
      If your Adam Equipment Scales display 'Err 5', it indicates an improper operation. Turn the balance off and back on again.
  • C
    Carol FosterSep 9, 2025
    What does the low battery indicator mean on Adam Equipment HCB 123?
    • C
      Craig KellySep 9, 2025
      If you see the low battery indicator, the internal battery may be flat. Charge the battery or replace the internal rechargeable battery.

Summary

3.0 SET UP

3.1 UNPACKING AND SETTING UP YOUR BALANCE

Steps for unpacking and assembling the balance, including draft shield.

3.2 DISPLAY; KEYBOARD FUNCTION

Explanation of the balance's display and the functions of each key.

3.3 INTERNAL RECHARGEABLE BATTERY

Information on operating the balance with its internal battery and charging.

3.4 LOCATING AND PROTECTING YOUR BALANCE

Guidelines for placing and protecting the balance from environmental factors.

3.5 STORING WHEN NOT IN USE

Instructions on how to stack and store the balance when it is not in use.

4.0 BASIC OPERATION

4.1 TURNING ON THE BALANCE

Procedure for powering the balance on and off, and initial self-test.

4.2 ZEROING; TARE

How to set the zero point or tare the balance with a container.

4.3 WEIGHING

Steps for performing a basic weighing operation with the balance.

4.4 WEIGHING UNITS

How to change and select different weighing units.

5.0 FUNCTIONS

5.1 PERCENTAGE WEIGHING

Explains how to use the balance for percentage weighing.

5.2 PARTS COUNTING

Guide to using the balance for counting small parts.

5.3 ACCUMULATION

Details on automatic and manual accumulation of weights.

6.0 PARAMETERS

6.1 ENABLING WEIGHING UNITS

How to enable or disable available weighing units for the user.

6.2 SETTING THE BACKLIGHT AND AUDIBLE ALERT BEEP

Configuration options for backlight and audible alerts.

6.3 SETTING THE PRINTING PARAMETERS; ACCUMULATION

Settings for outputting data to printers or PCs and accumulation.

6.4 AUTO POWER OFF

Configuration for the automatic power-off feature to save energy.

6.5 SELECTING THE INTERNAL OR EXTERNAL CALIBRATION

Option to choose between internal or external calibration methods.

6.6 ADJUST THE VALUE OF THE INTERNAL MASS

How to adjust the internal calibration weight value.

6.7 SETTING USER PARAMETERS

Adjusting user-specific settings like filter and stability.

7.0 CALIBRATION

Internal Calibration using HandiCal

Step-by-step guide for performing internal calibration using the HandiCal system.

External Calibration

Instructions for calibrating the balance using external weights.

8.0 TROUBLE SHOOTING

8.1 ERROR MESSAGES

Explains common error codes, their causes, and solutions.

8.2 REPLACEMENT PARTS AND ACCESSORIES

List of available spare parts and accessories for the balance.

9.0 SPECIFICATIONS

9.1 TECHNICAL SPECIFICATIONS

Detailed technical specifications for various models.

9.2 COMMON SPECIFICATIONS

General specifications applicable to all models.

9.3 RS-232; USB SPECIFICATIONS

Details on serial and USB communication interface parameters.

10.0 CALIBRATION CERTIFICATE

11.0 WARRANTY STATEMENT

Adam Equipment HCB 123 Specifications

General IconGeneral
BrandAdam Equipment
ModelHCB 123
CategoryScales
LanguageEnglish

Related product manuals