ADC EcoWash EWR-60 MC

Questions and Answers

P
pgarciaAug 18, 2025
What to do if PWR FAUL UAIT error message appears on ADC EcoWash Washer after a power cut?
- D
  Derrick CampbellAug 18, 2025
  If you see the PWR FAUL UAIT error message on your ADC EcoWash Washer after a power cut, you can either press START to continue the program from where it left off, or press ESC to end the program.
D
David MeyerAug 20, 2025
What to do if E4 FAULT WATER INLET error message appears on ADC EcoWash Washer?
- H
  Heather MooreAug 20, 2025
  If the E4 FAULT WATER INLET error message appears, you can press START to continue the program or press ESC to end it.
K
Kimberly WilcoxAug 23, 2025
What to do if E3 FAULT DRAIN PIPE error message appears on ADC EcoWash EWR-60 MC Washer?
- K
  Kevin RichardsonAug 23, 2025
  If the E3 FAULT DRAIN PIPE error message appears, you can press START to continue the program, or press ESC to end the program.
A
Anna JohnstonAug 26, 2025
What to do if E5 HEATING FAULT error message appears on ADC EcoWash EWR-60 MC?
- M
  millermonicaAug 26, 2025
  If the E5 HEATING FAULT error message appears, you can press START to continue the program or press ESC to end it.
A
Amanda ColemanAug 28, 2025
What to do if E6 MAX. TEMP error message appears on ADC EcoWash EWR-60 MC?
- M
  Miss Lori WilliamsAug 28, 2025
  If the E6 MAX. TEMP error message appears, you can press START to continue the program, or press ESC to end the program.
L
lauriealvarezAug 30, 2025
What to do if E7 THERMOSTAT OPEN error message appears on ADC EcoWash Washer?
- J
  Jacqueline MillerAug 31, 2025
  If the E7 THERMOSTAT OPEN error message appears, you can press START to continue the program or press ESC to end it.
P
Paul CollinsSep 2, 2025
What to do if E9 MOTOR HEATING error message appears on ADC EcoWash Washer?
- T
  Timothy SimmonsSep 2, 2025
  If the E9 MOTOR HEATING error message appears, you can press START to continue the program or press ESC to end it.
L
Laura SmithSep 4, 2025
What to do if E2 FAULT LOCK error message appears on ADC EcoWash Washer?
- L
  leebeverlySep 4, 2025
  If you see the E2 FAULT LOCK error message on your ADC EcoWash Washer, press ESC to end the program.
D
Debra MartinSep 7, 2025
What to do if E10 UNBALANCE error message appears on ADC EcoWash Washer?
- E
  Elizabeth RogersSep 7, 2025
  If the E10 UNBALANCE error message appears on the ADC EcoWash Washer, press ESC to end the program.
S
Sarah GriffithSep 9, 2025
What to do if E11 CLOTHES HOT error message appears on ADC EcoWash EWR-60 MC Washer?
- K
  Kirsten SmithSep 9, 2025
  If the E11 CLOTHES HOT error message appears on the ADC EcoWash Washer, press ESC to end the program.